background image

Power tools that are no longer usable should not be disposed of with 

household waste but in an environmentally friendly way. Please recycle 

where facilities exist. Check with your local council authority for 

recycling advice.

Recycling packaging reduces the need for landfill and raw materials. 

Reuse of recycled material decreases pollution in the environment. 

Please recycle packaging where facilities exist. Check with your local 

council authority for recycling advice.

DESCRIPTION OF SYMBOLS

CARING FOR THE ENVIRONMENT

Spare parts can be ordered from the Special Orders 

Desk at your local Bunnings Warehouse. 
For further information, or any parts not listed here, 
visit www.ozito.com.au or contact Ozito Customer 
Service: 
Australia 1800 069 486 
New Zealand 0508 069 486 
E-mail: [email protected]

SPARE PARTS

THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR YOUR 

BATTERY CHARGER.

1. 

Before using the charger read all instructions and cautionary markings on the charger, battery pack 

and the product using the battery pack.

2. 

This charger is not intended for any uses other than charging rechargeable batteries. Any other use 

may result in risk of fire, electric shock or electrocution.

3. 

Do not place any object on top of the charger or place the charger on a soft surface that may result in 

excessive internal heat. Place the charger in a position away from any heat source.

4. 

To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when 

disconnecting the charger.

5. 

Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected 

to damage or stress.

6. 

An extension cord should not be used unless absolutely necessary. Use of an improper extension cord 

could result in the risk of fire, electric shock or electrocution.

7. 

Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any 

way. Have it checked by an electrician or power tool repairer.

8. 

Do not disassemble charger. Take it to an electrician or power tool repairer when service or repair is 

required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.

9. 

To reduce risk of electric shock, unplug the charger from the outlet before attempting any cleaning. 

Removing the battery pack will not reduce this risk.

10. 

Never attempt to connect 2 chargers together.

11. 

DO NOT store or use the tool and battery pack in locations where the temperature may reach or exceed 

40ºC (such as inside sheds or metal buildings in summer).

12. 

The charger is designed to operate on standard household electrical power (240 volts). Do not attempt 

to use it on any other voltage!

13. 

The battery pack is not fully charged out of the carton. First read the safety instructions and then 

follow the charging notes and procedures.

14. 

The longest life and best performance can be obtained if the battery pack is charged when the air 

temperature is between 18 - 24ºC. Do not charge the battery pack in an air temperature below 10ºC or 

above 40ºC. This is important and will prevent damage to the battery pack.

15. 

Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The battery 

can explode in a fire.

16. 

Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or 

cracks, immediately discontinue use and do not recharge.

17. 

During charging, the battery must be placed in a well ventilated area.

BATTERY AND CHARGER SAFETY WARNINGS

Warning 

Read instruction manual

 

    

Diameter

      

 

mA

     

Milliamperes 

 

 

Recycle battery 

 

 

 

Do not put in the rubbish

Do not incinerate   

 

 

Do not get battery wet

Thermal cut-out protection

Transformer Energy

Rating (MEPS)

Double insulated 

 

Ah 

   

Amp hour

Indoor use only

Lithium Ion battery

Do not use or store battery in 

temperatures exceeding 50

º

C

   

     

n

o      

No load speed

  

V

 

    

Volts

 

 

 

            

Hz

      

Hertz

ac/~

      

Alternating current 

            

W

 

    

Watts

  

    

Direct current

 

 

dc/

Do not expose to rain.

Regulatory Compliance 

Mark (RCM)

     

Summary of Contents for PXCSK-700









Reviews: