CLEANING OF PAINTED SURFACES
Application of Soap
•
Wetting the surface first is not recommended, it dilutes the detergent and
reduces its effectiveness.
• Apply horizontally from side to side starting from bottom to avoid streaking.
• Avoid working on hot surfaces or in direct sunlight to minimize the chances
of the soap damaging painted surfaces.
• Damage may occur to painted surfaces if the soap is allowed to dry on the
surface.
• Hold the nozzle far enough away from surface to prevent damage to the
surface.
• Allow soap to remain on the surface for a short time before rinsing.
Rinsing
Rinse with clean water under high pressure. On a vertical surface, first rinse
from the bottom up, then rinse from top down. Hold nozzle minimum of 150mm
(6”) from the work surface at a 45° angle using the flat spray.
OPERATION
Symptom
Possible Cause
Corrective Action
Engine wil not
start or stops
while operating
Low-oil shutdown
Fill engine with oil
On/Off Switch not in
“ON” position
Turn switch “ON”
Pressure built up in
hose
Squeeze trigger while starting
Engine is
overloaded
Nozzle partially
blocked
Clean Nozzle
Pressure
increases when
gun is locked
Bypass valve blocking
Clean the bypass valve
Engine is running
but pump won’t
build maximum
pressure or has
irregular pressure
Tap supplying water
is off
Turn on tap
Inadequate water
supply
Provide a minimum of 15L/min
at 20 PSI
Kink in garden hose
Straighten garden hose
Spray Nozzle worn or
damaged
Replace Nozzle
Air in pump
Run with Gun on & Spray
Nozzle removed until a steady
stream of water is released
Pump inlet or outlet
blocked
Clean the pump inlet or outlet
No intake of
chemicals
Siphon tube not
securely inserted into
unit
Push tube firmly onto
connector
Tube cracked or split
Replace tube
Wrong Spray Nozzle
Switch to low pressure (Black)
Spray Nozzle
Trigger will not
move
Gun safety lock
engaged
Release safety lock
Rough/vibrating
operation with
pressure loss
Pump inlet restriction
Check system for stoppages,
air leaks, correctly sized inlet
plumbing to pump
Air in pump/water
Check inlet lines for restrictions
and or proper sizing
TROUBLESHOOTING
/min
Revolutions or
reciprocation per minute
l
Litres
dB
Decibel level
psi
Pounds per square inch
BAR
Pressure rating
Regulator compliance mark
Warning
Read instruction manual
Hot Surface
Do not expose to rain
Hp
Horse power
cc
Cubic Centimeters (the standard measure of displacement in Europe
and Asia)
DESCRIPTION OF SYMBOLS
High Pressure Hose
SPPWB2800-07
High Pressure Gun & Lance
SPPWB2800-36
Spray Nozzle Set
SPPWB2800-42
Spare parts can be ordered from the Special Orders Desk at your local
Bunnings Warehouse.
For further information, or any parts not listed here, visit www.ozito.com.
au or contact Ozito customer service
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
CARING FOR THE ENVIRONMENT
Petrol tools that are no longer usable should not be disposed
of with household waste but in an environmentally friendly way.
Please recycle where facilities exist. Check with your local council
authority for recycling advice.
Recycling packaging reduces the need for landfill and raw
materials. Reuse of recycled material decreases pollution in the
environment. Please recycle packaging where facilities exist.
Check with your local council authority for recycling advice.
CAUTION:
USE ONLY LIQUID DETERGENTS DESIGNED
SPECIFICALLY FOR USE WITH PRESSURE WASHERS.
ONLY USE CHEMICALS COMPATIBLE WITH THE ALUMINUM
AND BRASS PARTS. POWDERED SOAPS MAY CLOG
THE INJECTION SYSTEM. ALWAYS USE CHEMICALS
ACCORDING TO THE MANUFACTURERS DIRECTIONS.
1. Attach siphon
tube to the
detergent siphon
connector on the
pump.
2. Ensure the strainer at the end of the siphon tube is not clogged or
obstructed in any way.
3. Insert the siphon tube
to the bottom of the
detergent container
4. Install the
black spray
nozzle onto
the lance.
Detergent Siphon
Most cleaning tasks can be completed with the pressure washer
alone. For others, it is advantageous to use detergent. Use only liquid
detergents designed specifically for use with pressure washers.
5. The detergent will automatically mix with the water and discharge
through the nozzle.
6. After using the detergent siphon, remove siphon tube from soap
container, and place into a container of clean water to flush out
any residual soap.
