Ozito Power X Change PXCBLSS-018 Page 9 Instruction Manual Download

Page: 9 / 16

2. ADJUSTING THE TRIMMER

1. Place the big hole in the blade

onto the blade mount on the

bottom of the spindle plate.

3. To remove the blade push the

blade towards the centre of the

spindle and then slide off.

2. Pull the blade outwards

so that the small hole is

fitted into the mount.

Attaching a Blade

Adjusting the Height

1. Loosen the shaft adjustment

collar.

2. Extend to the desired

height and then retighten

the shaft adjustment

collar to secure in place

Adjusting the Secondary Handle

1. Loosen the locking knob.

2. Rotate the handle into the

desired position and then

tighten the locking knob.

Fitting the Flower Guard

1. Attach the flower guard to

the motor housing.

Summary of Contents for Power X Change PXCBLSS-018

















Search results

Summary of Contents for Power X Change PXCBLSS-018

Reviews:

Related manuals for Power X Change PXCBLSS-018

Brands by name

Popular brands

Ozito Power X Change PXCBLSS-018, Instruction Manual

Search results

Summary of Contents for Power X Change PXCBLSS-018

Reviews:

Related manuals for Power X Change PXCBLSS-018

Brands by name

Popular brands