Ozito Power X Change PXCBLSS-018 Instruction Manual Download

Page: 3 / 16

3. CONTROLS

2. INSERTING & REMOVING THE BATTERY

OPERATION

1. Align the ribs of the battery with

the recess in below the handle.

1. Press and hold the battery

release tab to release the

battery.

2. Slide the battery in so

that it clicks into place.

1. To start the blower

squeeze the on/off

switch.

2. To stop the blower

release the on/off

switch.

2. Slide the battery out.

Inserting the Battery Pack

Removing a Battery from the Blower

Switching On and Off

WARNING!:

DO NOT USE THE BLOWER WITH ANY

TYPE OF ACCESSORY OR ATTACHMENT. SUCH
USAGE MIGHT BE HAZARDOUS.

WARNING!:

DO NOT PUT PART OF YOUR BODY

SUCH AS HANDS AND FINGERS NEAR THE INLET
OR OUTLET OPENING.

WARNING!

DO NOT USE ANY ATTACHMENTS

OR ACCESSORIES NOT RECOMMENDED BY THE

MANUFACTURER OF THIS PRODUCT, AS IT CAN

RESULT IN SERIOUS PERSONAL INJURY.

Summary of Contents for Power X Change PXCBLSS-018

















Search results

Summary of Contents for Power X Change PXCBLSS-018

Reviews:

Related manuals for Power X Change PXCBLSS-018

Brands by name

Popular brands

Ozito Power X Change PXCBLSS-018, Instruction Manual

Search results

Summary of Contents for Power X Change PXCBLSS-018

Reviews:

Related manuals for Power X Change PXCBLSS-018

Brands by name

Popular brands