manualshive.com logo in svg

Ozito Power X Change PXCBLSS-018, Instruction Manual

Share
Download
Ozito Power X Change PXCBLSS-018 Instruction Manual Download Page 4

PXCBLSS-018

Blowing

The blower is ideal for 

blowing leaves, grass 

clippings and other debris. 

The split tube allows for easy 

cleaning of outdoor furniture 

while the full-length tube 

makes easy work on paths and 

driveways.

Hold the blower firmly, 

squeeze the on/off switch, 

point the jet of air in front of 

you and move forward slowly. 

Move the blower from side to 

side, with the tube several inches 

above the ground.

Be careful where you point the 

jet of air as it can move heavy 

material and cause injury or 

damage to bystanders.

Note:

 Be aware of other people 

and animals in the area where you are to be operating the blower.

Note:

 

Avoid collisions with hard objects which could damage your machine.

4.  OPERATION

WARNING!: 

DO NOT SWITCH THE BLOWER ON 

IN ENCLOSED OR POORLY VENTILATED SPACES 
OR IN THE PRESENCE OF FLAMMABLE AND/OR 
EXPLOSIVE LIQUIDS, GASES AND POWDERS.

Summary of Contents for Power X Change PXCBLSS-018

















Reviews:

No comments

Brands by name

Popular brands

Load more brands