background image

TROUBLESHOOTING

DESCRIPTION OF SYMBOLS

MAINTENANCE

Cleaning

•  We recommend that you clean the appliance immediately after you 

use it.

•  Keep the safety devices free of dirt and dust as much as possible. 

Wipe the equipment with a clean cloth.

•  Clean the appliance regularly with a damp cloth and some soft 

soap. Do not use cleaning agents or solvents; these may be 

aggressive to the plastic parts in the appliance. Ensure that no 

water can get into the interior of the appliance.

Storage

Keep in a dry frost free location, out of reach of children.

Note: 

Ozito Industries will not be responsible for any damage or 

injuries caused by the repair of the tool by an unauthorised person or 

by mishandling of the tool.

Sparking visible through the housing air vents

A small amount of sparking may be visible through the housing vents. 

This is normal and does not indicate a problem.

The tool loses power during use

•  Battery could be low and requires charging.
•  The tool could have overloaded due to excessive pressure. Turn 

the product back on and reduce the load.

LED Collar does not turn on

•  Battery could be low and require replacing. 

Undo the 3 screws on the back of the LED collar and replace the 

2 CR927 batteries. Take note of the direction of the button cell 

batteries when replacing them.

  

n

0

 

    

No Load Speed

 

   

 

    

  

 

 

Double Insulated

 

    

Warning

Regulatory Compliance Mark

(RCM)

Read Instruction Manual

Power tools that are no longer usable should not be 

disposed of with household waste but in an environmentally 

friendly way. Please recycle where facilities exist. Check 

with your local council authority for recycling advice.

Recycling packaging reduces the need for landfill and raw 

materials. Reuse of recycled material decreases pollution in 

the environment. Please recycle packaging where facilities 

exist. Check with your local council authority for recycling 

advice.

CARING FOR THE ENVIRONMENT

SPARE PARTS

Spare parts can be ordered from the Special Orders Desk 

at your local Bunnings Warehouse. 
For further information, or any parts not listed here, visit 
www.ozito.com.au or contact Ozito Customer Service: 
Australia 1800 069 486 
New Zealand 0508 069 486 
E-mail: [email protected]

Summary of Contents for LRTK-036









Reviews: