background image

Installing A Wire Spool

The welder can be fitted with 0.8mm or 0.9mm gasless welding 

wire. Welding wire up to 1kg can be fitted to this welder.

1.  Push the latch towards the back of the 

welder unit and lift the top cover.

2.  Undo the spool nut then 

remove the spring and spool 

plate.

Note:

 Before first use, be sure to 

remove all the packaging from 

the included wire spool.

WARNING! 

DO NOT PULL THE END OF THE WIRE FREE 

UNTIL YOU ARE READY TO THREAD THE MACHINE. THE 

SPOOL IS COILED UNDER TENSION AND WILL UNWIND 

IF RELEASED WHICH MAY CAUSE TANGLING & WIRE 

FEED ISSUES DURING USE.

3.  Place the spool onto the 

spindle so that the wire 

unwinds in an anti-clockwise 

direction.

4.  Replace the spool plate and 

spring, then lock it in place 

with the spool nut.

5.  Flip the tension adjustor bar 

up and swing the pressure 

arm away from the roller 

guide.

6.  While maintaining a firm hold 

of the wire end, pull it free of 

the spool and thread it through 

the feed tube and into the 

cable housing.

7.  Rotate the pressure arm back 

into place and flip the tension 

adjustor bar back to lock it in 

place.

Assembling The Welding Mask

The included welding mask must be fitted with the lens assembly 

and handle before using it for welding.

1.  Push the plastic pins into the 

mask from the outside and 

secure it with the retaining 

clips from the inside of the 

mask. Rotate the retaining 

clips so that the lens assembly 

can be inserted.

2.  Insert the clear glass into the 

recess of the welding mask, 

then the dark safety glass and 

finally the plastic lens frame.

3.  Rotate the retaining clips to 

lock the lens assembly in 

place.

4.  Bend the sides and top of the 

welding mask inwards and 

clip it together at the corners.

5.  Insert the 3 screws into the 

handle mounting holes from 

the outside. Fit the handle onto 

the screws on the inside of the 

mask and secure them using 

the 3 nuts.

2. ASSEMBLY

3. SETTING UP THE WELDING WIRE

WARNING! 

ENSURE THE TOOL IS TURNED OFF AND 

DISCONNECTED FROM THE POWER SUPPLY BEFORE 

PERFORMING ANY OF THE FOLLOWING OPERATIONS.

WARNING! 

ALWAYS ENSURE THE WELDER IS 

SWITCHED OFF WHEN REPLACING THE WELDING WIRE 

&/OR MAKING ADJUSTMENTS TO THE WIRE DRIVE 

SYSTEM.

a

b

a

b

Summary of Contents for IMW-100





















Reviews: