background image

I

0

AC 240V ~ 50Hz

OFF

ON

AC POWER

ON

THERMAL

OVERLOAD

ALLOW

WELDER
TO COOL

DOWN

!

100A

INVERTER 

MIG WELDER

VOLTAGE

MIN

MAX

FEED RATE

MIN

MAX

Safety Precautions

•  Read all safety warnings and all instructions before use. Failure 

to follow the warnings and instructions may result in electric 

shock, fire and/or serious injury.

•  Always wear appropriate protective equipment when welding. 

These include: welding helmets, overalls, welding gloves, closed 

shoes, leather apron, sock protectors. Overalls should be of the 

type designed to be buttoned at the wrists and the neck.

•  Remove loose clothing and accessories and ensure any loose 

hair is tied up or tucked away.

•  Toxic gases are given off during the welding process, which 

may collect in the welding area. Always ensure to weld in a 

well-ventilated area and use a fume extractor when required.

•  The electric arc generated by the welding process gives direct 

heat and ultraviolet radiation. It is essential that the eyes of 

the operator and any bystanders are protected from the glare 

during welding. ALWAYS use a face shield or welding helmets 

fitted with the correct glass filter.

•  Inspect the welder, welding torch and all connecting wires for 

damage / worn insulation before each use and if any damage is 

found, replace the damaged parts before use.

•  Parts of the welding torch and welding material can be 

extremely hot immediately after welding. Wait for the electrode 

and the material to cool down before handling and always 

ensure welding gloves are worn when handling hot materials.

WARNING! 

ENSURE ALL OIL, PETROL AND 

FLAMMABLE CONTAINERS HAVE BEEN REMOVED 

FROM THE WELDING AREA.

1.  On/Off Switch 

2.  AC Power Cord

3.  Power ON LED

4.  Thermal Overload LED

5.  Voltage Control Dial

6.  Feed Rate Control Dial

7.  Torch

8.  Earth Clamp

9.  Torch Tip

10. Torch Shroud

SELF SHIELDED FLUX CORED INVERTER ARC WELDER

KNOW YOUR PRODUCT

1. BEFORE STARTING

SETUP & PREPARATION

4

8

3

7

1

10

9

2

5

6

ONLINE MANUAL

Scan this QR Code with your mobile 

device to take you to the online manual.

Summary of Contents for IMW-100





















Reviews: