background image

MAINTENANCE

DESCRIPTION OF SYMBOLS

Cleaning

1.  We recommend that you clean the tool immediately after you use it.

2.  Keep the tool free of dirt and dust as much as possible. Wipe the 

equipment with a clean cloth.

3.  Clean the tool regularly with a cloth. Do not use cleaning agents 

or solvents; these may be aggressive to the plastic parts in the 

appliance.

4.  You must disconnect the hose and spraying tools from the pressure 

washer before cleaning. Do not clean the pressure washer with 

water.

Storage

Pull the mains plug out of the socket, switch off the tool and make 

sure that it is secured in such a way that it cannot be started up again 

by any unauthorised person.

The nozzle can be stored on the accessory slots on the back of the 

unit when not in use. Wind the water hose around the handle hook 

and the power cord around the cord hook to keep them tidy and out 

of the way.

Empty the detergent bottle before storing the tool in a dry location 

which is not accessible to unauthorised persons.

Supply Cords

If replacement of the supply cord is necessary, this has to be done by 

a certified electrician in order to avoid a safety hazard.

Note: 

Ozito Industries will not be responsible for any damage or 

injuries caused by the repair of the tool by an unauthorised person or 

by mishandling of the tool.

WARNING! 

BEFORE CLEANING YOUR TOOL OR 

CARRYING OUT ANY MAINTENANCE PROCEDURE, 

MAKE SURE THAT IT IS DISCONNECTED FROM 

THE POWER SUPPLY TO PREVENT ACCIDENTAL 

STARTING.

Wear gloves

Wear eye protection

Ingress protection from water

Warning

Regulatory Compliance Mark

(RCM)

Machine not suitable for

connection to the potable water

mains

Warning! High pressure jets can be

dangerous if not used properly. Do 

not direct the jet at persons, 

animals, live electrical equipment 

or the pressure washer itself.

Double insulated

V

Volts

Hz

W

Hertz

~

psi

IPX5

L/min

Alternating Current

Watts

Pounds per square inch

Litres per minute

MPa

Mega Pascals

Read Instruction Manual

Power tools that are no longer usable should not be 

disposed of with household waste but in an environmentally 

friendly way. Please recycle where facilities exist. Check 

with your local council authority for recycling advice.

Recycling packaging reduces the need for landfill and raw 

materials. Reuse of recycled material decreases pollution in 

the environment. Please recycle packaging where facilities 

exist. Check with your local council authority for recycling 

advice.

CARING FOR THE ENVIRONMENT

SPARE PARTS

Spare parts can be ordered from the Special Orders Desk 

at your local Bunnings Warehouse. 
For further information, or any parts not listed here, visit 
www.ozito.com.au or contact Ozito Customer Service: 
Australia 1800 069 486 
New Zealand 0508 069 486 
E-mail: [email protected]

Summary of Contents for HPW-2400









Reviews: