background image

Adjusting The Spray Jet

The water jet output can be controlled when using the adjustable 

spray nozzle.

1.  Turn the nozzle  clockwise for 

a narrow jet over a small area 

for concentrated cleaning.

2.  Turn the nozzle anti-clockwise 

for a wide, fan jet to clean 

larger areas faster. 

Overload Protection

The tool is equipped with an overload protection feature. If an 

overload occurs, the tool will automatically shut off to protect the tool. 

1.  In the event of an overload 

turn the on/off dial to the ‘0 | 

OFF’ position, allow the tool to 

cool down completely. 

2.  Remove the power plug from the mains socket and disconnect the 

garden hose from the water inlet port.

3.  Unscrew the hose adaptor 

from the water inlet port and 

inspect the mesh filter for any 

blockages. 

4.  Clean the filter as necessary 

and reinstall it when done.

5.   Once the unit has cooled sufficiently, restart the unit and use as 

normal.

WARNING! 

DO NOT CONTINUE USING THE 

UNIT IF THE OVERLOAD SWITCH TRIPS AGAIN 

IMMEDIATELY AFTER THE RESET.

WARNING! 

WHEN INSPECTING EQUIPMENT FOR 

FAULTS, ENSURE THE UNIT IS SWITCHED OFF AND 

THE POWER CABLE IS DISCONNECTED BEFORE 

CARRYING OUT INSPECTION.

HPW-2400

4. PRESSURE WASHING

HIGH PRESSURE WASHER

0 | OFF

I | ON

Flat Fan

Solid Cone

Quick Start Procedure

1.  With the adjustable spray 

nozzle attached, adjust it to 

the widest spray setting.

2.  Attach the garden hose to the 

water inlet port and turn on 

the water at the tap.

3.  Squeeze the spray gun trigger 

to prime the pump and purge 

any air from the system.

4.  Plug the power cord into mains power.

5.  Turn the unit on using the on/

off dial to start washing.

WARNING! 

ENSURE THE PRESSURE WASHER IS 

PLACED ON A FLAT, HARD SURFACE. ALWAYS 

HAVE THE PRESSURE WASHER IN AN UPRIGHT 

POSITION DURING USE.

HIGH PRESSURE WASHER

0 | OFF

I | ON

Solid Cone

WARNING! 

ENSURE THAT THE SPRAY JET IS 

NOT DIRECTED AT POWER LINES, ELECTRICAL 

OUTLETS AND ELECTRONICS.

WARNING! 

HIGH PRESSURE HOSES, FITTINGS & 

COUPLINGS ARE IMPORTANT FOR THE SAFETY 

OF THE USER. USE ONLY HOSES, FITTING & 

COUPLINGS SUPPLIED.

WARNING! 

WEAR SAFETY GLASSES WHEN USING 

THE PRESSURE WASHER TO AVOID FLYING DEBRIS 

THAT MAY BE DISLODGED DURING CLEANING.

WARNING! 

DO NOT POINT THE SPRAY JET AT ANY 

PART OF YOUR BODY, OTHER PEOPLE, PETS OR 

ANIMALS. THE PRESSURISED WATER STREAM CAN 

CAUSE SERIOUS CUTS AND INJURIES.

Summary of Contents for HPW-2400









Reviews: