background image

0

25

50

75

100

125

150

0

(1)00

(3)00

(5)00

(7)00

(9)00

2

4

6

8

10

Lb/in²
(PSI)

kPA

(BAR)

PRESSURE GAUGE

kg/cm²

0

25

50

75

100

125

150

0

(1)00

(3)00

(5)00

(7)00

(9)00

2

4

6

8

10

Lb/in²
(PSI)

kPA

(BAR)

PRESSURE GAUGE

kg/cm²

AIR COMPRESSOR

2.0HP 40L 

1.  Motor
2.  On/Off Switch
3.  Pressure Regulator
4.  Carry Handle
5.  Regulated Pressure Outlet
6.  Regulated Pressure Gauge

7.  Support Foot
8.  Drain Valve
9.  Pressure Tank
10. Wheel
11. Tank Handle
12. Tank Pressure Gauge

AIR COMPRESSOR

KNOW YOUR PRODUCT

1. ASSEMBLY

SETUP & PREPARATION

1

2

3

4

5

6

7

8

10

11

9

12

ONLINE MANUAL

Scan this QR Code with your mobile 
device to take you to the online manual.

Pre-Setup Checks

•   Examine the machine for signs of transit damage. If damaged, 

do not use, return to place of purchase 

•   The compressor should be set up near to the user.
•   Avoid long air lines and long supply lines (extensions).
•   Make sure the intake air is dry and dust-free.
•   Do not set up the compressor in damp or wet rooms. The 

compressor is designed to be used in dry rooms. It is prohibited 
to use the compressor in areas where work is conducted with 
sprayed water. 

•   Before you use the machine, make sure that the mains voltage 

complies with the specifications on the rating plate. 

•   The compressor may only be used in suitable areas (with good 

ventilation. There must be no dust, acids, vapours, explosive or 
flammable gases in the room.

WARNING! 

ENSURE THE TOOL IS TURNED OFF AND 

DISCONNECTED FROM THE POWER SUPPLY BEFORE 
PERFORMING ANY OF THE FOLLOWING OPERATIONS.

Summary of Contents for ACP-4025









Reviews: