background image

DESCRIPTION OF SYMBOLS

Cleaning

1.  We recommend that you clean the appliance immediately after 

you use it.

2.  Keep the safety devices free of dirt and dust as much as 

possible. Wipe the equipment with a clean cloth.

3.  Clean the appliance regularly with a damp cloth and some soft 

soap. Do not use cleaning agents or solvents; these may be 

aggressive to the plastic parts in the appliance. Ensure that no 

water can get into the interior of the appliance.

4.  You must disconnect the hose and any spraying tools from the 

compressor before cleaning. Do not clean the compressor with 

water, solvents or the like.

Storage

Switch off the compressor, pull the mains plug out of the socket, 

and ventilate the appliance and all connected pneumatic tools. 

Drain the pressure tank.

Make sure that it is secured in such a way that it cannot be started 

up again by any unauthorised person.

Store the tool in a dry location which is not accessible to 

unauthorised persons.

Supply Cords

If replacement of the supply cord is necessary, this has to be done 

by a certified electrician in order to avoid a safety hazard.

Note: 

Ozito Industries will not be responsible for any damage or 

injuries caused by the repair of the tool by an unauthorised person 

or by mishandling of the tool.

WARNING! 

BEFORE CLEANING THE APPLIANCE OR 

CARRYING OUT ANY MAINTENANCE PROCEDURE, 

MAKE SURE THAT IT IS DISCONNECTED FROM THE 

POWER SUPPLY TO PREVENT ACCIDENTAL STARTING.

Sound Power Level

Wear hearing protection

Warning

Regulatory Compliance Mark

(RCM)

V

Volts

Hz

W

Hertz

~

n

0

/min

Alternating Current

Watts

No load speed

Revolutions or reciprocations 

per minute

Read Instruction Manual

Beware of electrical voltage

Beware of hot parts.

Pressure rating

Do not open the outlet before 

the air hose is attached

bar

L

Litres

No protection against ingress

from water

lP20

Warning! The equipment is

remote-controlled and may 

start-up without warning.

Power tools that are no longer usable should not 

be disposed of with household waste but in an 

environmentally friendly way. Please recycle where 

facilities exist. Check with your local council authority for 

recycling advice.

Recycling packaging reduces the need for landfill and raw 

materials. Reuse of recycled material decreases pollution 

in the environment. Please recycle packaging where 

facilities exist. Check with your local council authority for 

recycling advice.

CARING FOR THE ENVIRONMENT

SPARE PARTS

Spare parts can be ordered from the Special Orders Desk at your 

local Bunnings Warehouse. 
For further information, or any parts not listed here, visit  
www.ozito.com.au or contact Ozito Customer Service: 
Australia 1800 069 486 
New Zealand 0508 069 486 
E-mail: [email protected]

Summary of Contents for 40L 2.5HP









Reviews: