background image

6. APPLIANCE CARE

5. TROUBLESHOOTING

MAINTENANCE

Draining The Pressure Tank

WARNING! 

RELEASE ALL AIR PRESSURE FROM THE 

TANK BEFORE OPENING THE DRAIN VALVE. TAKE CARE 

WHEN DISCHARGING AIR THROUGH THE DRAIN VALVE 

OR AIR OUTLETS. THE DISCHARGED AIR CAN CAUSE 

DUST, STONES, OR ANY OTHER FOREIGN PARTICLES 

TO BE BLOWN THROUGH THE AIR AT HIGH PRESSURE.

Air in the compressor tank causes water to accumulate. This must 

be drained off frequently to prevent corrosion and damage to the 

unit. 

This should be performed after each use and prior to the 

next use.

1.  Turn the drain valve plug clockwise to open it.

2.  Allow all of the water in the 

tank to drain out.

3.  Replace the drain valve plug.

Note: 

The tank will not pressurise while the drain valve is open. 

0

25

50

75

100

125

150

0

(1)00

(3)00

(5)00

(7)00

(9)00

2

4

6

8

10

Lb/in²

(PSI)

kPA

(BAR)

PRESSURE GAUGE

kg/cm²

0

25

50

75

100

125

150

0

(1)00

(3)00

(5)00

(7)00

(9)00

2

4

6

8

10

Lb/in²

(PSI)

kPA

(BAR)

PRESSURE GAUGE

kg/cm²

AIR COMPRESSOR

2.5HP 40L 

Symptom

Possible Cause

Suggested Solution

The compressor does 

not start

Compressor has 

reached cut-out 

pressure

Compressor will 

automatically start 

once below the cut-in 

pressure.

No power supply

Check the power supply, 

the power plug and the 

socket-outlet.

Insufficient supply 

power

Reduce length of 

extension lead.

Outside temperature 

is too low

Never operate with an 

outside temperature of 

below 5°C.

Motor is overheated Allow the motor to cool 

down. If necessary, 

remedy the cause of the 

overheating.

The compressor 

starts but there is no 

pressure

The seals are 

damaged.

Check the seals and 

have any damaged seals 

replaced by a service 

centre.

The drainage valve 

leaks.

Ensure it is properly 

closed.

The compressor 

starts, pressure 

is shown on the 

pressure gauge, but 

no pressure to the 

air tool.

Loose hose 

connections

Check the compressed 

air hose and tools and 

replace if necessary.

Leak in a quick-lock 

coupling

Check the quick-lock 

coupling and replace if 

necessary.

Insufficient pressure 

set on the pressure 

regulator.

Open the pressure 

regulator further.

Summary of Contents for 40L 2.5HP









Reviews: