HINTS & TIPS
• Do not force the saw into the cut. Apply only light pressure whilst running the
engine at full throttle.
• If the saw chain gets caught in the cut, do not try to remove it by twisting the guide
or pulling forcibly. Use a lever or wedge to open up the cut so that the saw chain is
freed.
While cutting, always:
• Run the chainsaw motor at full revs. This makes the job safer, as there is less
chance of pull-in or kick-back.
• Position your body to the left of the chainsaw so if it kicks back uncontrollably, it
goes over your right shoulder, never stand in the cutting line of the saw.
•
Keep a firm grip with your left hand on the front handle, with your thumb securely
below the handle.
• The swivel of your wrist in a kick-back situation will activate the chain brake.
• Make sure the chain is tensioned correctly.
Replacing the spark plug
When the chainsaw will not start when everything else
has been checked, it is most likely the spark plug needs
replacing. The spark plug is not covered under warrantly.
To replace the spark plug:
1. Unscrew and remove the filter cover knob.
2. Remove the filter cover.
3. Pull the spark plug lead off the spark plug end.
4. Loosen (anti-clockwise) the spark plug using the
larger socket side of the double ended wrench provided.
5. Remove the spark plug and replace with a new one,
as specified.
Spark plug types: LD L8RTF, NGK BPMR7A,
Champion RCJ7Y
6. Secure the spark plug in position by tightening
(clockwise) the spark plug using the double ended
wrench provided.
7. Fix the spark plug lead back to the end of the spark
plug ensuring it clicks into place.
0.7mm
8. Replace the filter cover (19) and secure in place with the filler cover knob.
NOTE:
The chainsaw warranty does not cover components that have been
subjected to operator abuse or negligence. To receive full value from the warranty,
the operator must maintain the chainsaw as instructed in this manual.
Ozito Industries will not be responsible for any damage or injuries caused by repair
of the tool by an unauthorised person or mishandling or mistreatment of the tool.
This tool is designed for Domestic Home Use only - use in commercial or industrial
environments will void the warranty.
CARING FOR THE ENVIRONMENT
Petrol tools that are no longer usable should not be disposed of with
household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with yourlocal council authority
for recycling advice.
Recycling packaging reduces the need for landfill and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
Chain
ACCPCS-004
Guide
Bar SPPCS305-157
Ignitor
Assembly
SPPCS305-031
Damper
SPPCS305-140
Primer
Bulb
SPPCS305-048
Tension
Block
SPPCS305-134
Special Tool (Carburettor Adj.)
SPPCS305-160
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito customer service
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
DESCRIPTION OF SYMBOLS
cc
Cubic Centimeters (the standard measure of displacement in Europe and Asia)
n
o
No load speed
/min
Revolutions or reciprocation per minute
dB
Decibel level
Electrical Emissions Conformity (EMC)
Read the manual prior to use
Wear safety boots
Wear safety gloves
Warning
Be aware of moving branches
Pull recoil starter to start motor
Do not use chainsaw when
only holding with one hand
Use both hands when using chainsaw
Use eye, ear, head and breathing
protection when operating the chainsaw
Fuel inlet
(Position: under the fuel tank cap.)
On/Off
(Position: next to the oil tank cap)
Setting the on/off switch to Off,
stops the engine immediately
Choke control
(Position: next to knob on the filter cover)
Chain brake released (hollow arrow) and activated (solid arrow)
(Position: right side of machine, on chain drive cover)
CHOKE Start position (when engine is cold)
START Start position (when engine is warm)
RUN Run position
Chain oil inlet
(Position: next to the oil tank cap)
H
High run adjustment screw
L
Low run adjustment screw
T
Idel adjustment screw (Position: left side of
machine close to pull start handle)
