Owon SDS1022 User Manual Download Page 41

Page: 41 / 66

4.Advanced User Guidebook

●Display

Push the

Utility

button, select

Function

in the right menu, select

Display

in the left

menu.
The description of

Display

Menu

is shown as the follows:

●

Adjust

Push the

Utility

button, select

Function

in the right menu, select

Adjust

in the left

menu.
The description of

Adjust

Menu

is shown as the follows:

Do Self Cal (Self-Calibration)

The self-calibration procedure can improve the accuracy of the oscilloscope under the
ambient temperature to the greatest extent. If the change of the ambient temperature is
up to or exceeds 5

℃

, the self-calibration procedure should be executed to obtain the

highest level of accuracy.

Before executing the self-calibration procedure, disconnect all probes or wires from the
input connector. Push the

Utility

button, select

Function

in the right menu, the function

menu will display at the left, select

Adjust

. If everything is ready, select

Self Cal

in the

Function Menu

Setting

Description

Function

Configure

Show the configure menu

KeyLock

Lock all keys. Unlock method: push

Trigger

Menu

button in trigger control area, then push

Force

button, repeat

3 times.

About

Show the version and serial number

Function Menu

Setting

Description

Function

Display

Show the display menu

BackLight

0% - 100%

Turn the

knob to adjust the backlight.

Graticule

Select the grid type

Menu Time

OFF, 5S – 30S

Turn the

knob to set the disappear time

of menu

Function Menu

Description

Self Cal

Carry out the self-calibration procedure.

Default

Call out the factory settings.

ProbeCh.

Check whether probe attenuation is good.

Summary of Contents for SDS1022



































































Search results

Summary of Contents for SDS1022

Reviews:

Related manuals for SDS1022

Brands by name

Popular brands

Owon SDS1022, User Manual

Search results

Summary of Contents for SDS1022

Reviews:

Related manuals for SDS1022

Brands by name

Popular brands