Owon SDS1022 User Manual Download Page 42

Page: 42 / 66

4.Advanced User Guidebook

right menu to enter the self-calibration procedure of the instrument.

Probe checking

To check whether probe attenuation is good. The results contain three circumstances:
Overflow compensation, Good compensation, Inadequate compensation. According to the
checking result, users can adjust probe attenuation to the best. Operation steps are as
follows:
1.

Connect the probe to CH1, adjust the probe attenuation to the maximum.

Push the

Utility

button, select

Function

in the right menu, select

Adjust

in the left

menu.

Select

ProbeCh.

in the right menu, tips about probe checking shows on the screen.

Select

ProbeCh.

again to begin probe checking and the checking result will occur

after 3s; push any other key to quit.

●

Save

You can save the waveforms, configures or screen images. Refer to "

How to Save and

Recall a Waveform

" on page 28.

●

Update

Use the front-panel USB port to update your instrument firmware using a USB memory
device. Refer to "

How to Update your Instrument Firmware

" on page 37.

How to Update your Instrument Firmware

Use the front-panel USB port to update your instrument firmware using a USB memory
device.

USB memory device requirements

: Insert a USB memory device into the USB port on

the front panel. If the icon

appears on the top right of the screen, the USB memory

device is installed successfully. If the USB memory device cannot be detected, format the
USB memory device according to the methods in "

USB disk Requirements

" on P31.

Caution

: Updating your instrument firmware is a sensitive operation, to prevent damage

to the instrument, do not power off the instrument or remove the USB memory device
during the update process.

update your instrument firmware, do the following:

Push the

Utility

button, select

Function

in the right menu, select

Configure

in the left

menu, select

About

in the right menu. View the model and the currently installed

firmware version.

From a PC, visit

www.owon.com.cn

and check if the website offers a newer firmware

version. Download the firmware file. The file name must be Scope.update. Copy the
firmware file onto the root directory of your USB memory device.

Insert the USB memory device into the front-panel USB port on your instrument.

Push the

Utility

button, select

Function

in the right menu, select

Update

in the left

menu.

In the right menu, select

Start

, the messages below will be shown.

Summary of Contents for SDS1022



































































Search results

Summary of Contents for SDS1022

Reviews:

Related manuals for SDS1022

Brands by name

Popular brands

Owon SDS1022, User Manual

Search results

Summary of Contents for SDS1022

Reviews:

Related manuals for SDS1022

Brands by name

Popular brands