background image

Keep people clear of opening while
Door is moving.

Do Not

 allow children to play with

the Door operator.

Do Not

 operate a Door that jams or

one that has a broken spring.

POTENTIAL HAZARD

EFFECT

PREVENTION

MOVING DOOR

HIGH SPRING TENSION

WARNING:

 Can Cause

Serious Injury or Death

WARNING:

 Can Cause

Serious Injury or Death

Do Not

 try to remove, repair or adjust

springs or anything to which Door spring
parts are fastened, such as, wood blocks,
steel brackets, cables or other like items.

Repairs and adjustments must be made
by a trained service person using proper
tools and instructions.

Overhead doors are large, heavy objects that move with the help of springs under high tension
and electric motors. Since moving objects, springs under tension, and electric motors can
cause injuries, your safety and the safety of others depend on you reading the information in 
this manual. If you have questions or do not understand the information presented, call your
nearest service representative.

In this section and those that follow, the words

 Danger

Warning

 and 

Caution

 are used to 

emphasize important safety information. The word:

  

 DANGER

 means that severe injury or death will result from failure to follow instructions.

   

WARNING

 means that severe injury or death can result from failure to follow instructions.

   

CAUTION

 means that property damage or injury can result from failure to follow instructions.

The word 

NOTE

 is used to indicate important steps to be followed or important considerations. 

SAFETY INFORMATION

IMPORTANT

OVERVIEW OF POTENTIAL HAZARDS

READ THIS MANUAL CAREFULLY AND OBSERVE ALL WARNINGS WHEN INSTALLING,
OPERATING OR MAINTAINING YOUR OVERHEAD DOOR.

                 

CHECK for shipping damage.

CHECK door against packing list to make sure door 
is the same as ordered and all parts are included.

CHECK width and height of door opening against
sizes noted with shipment to assure that door will fit.

CHECK to make sure headroom and side clearances
are adequate (Figure 1).

                 

Read these instructions completely before 
attempting to install this door.

WARRANTY VOID IF DOOR IS NOT INSTALLED
ACCORDING TO INSTRUCTIONS.

DO NOT CUT OR REMOVE RETAINING BANDS
UNTIL INSTRUCTED TO DO SO.

CHECK WARNING LABELS ON DOOR FOR PROPER 
INSTALLATION PROCEDURE.

2

Summary of Contents for 780 CD Series














Reviews: