background image

en

21

Installation

Commissioning

Adjustments

Tr

oubleshooting

Data comm

unication

Heat pump mode

The 

HP mode

 can be used to force an afterheating, 

when a heat pump is used for the store afterheating. 
For that purpose, the store contents are mixed in or-
der to decrease the store temperature, which leads 
to a heat pump demand. 
When the heat pump mode has been activated, the 
optimum operating temperature of the heat pump 

T-HP opt

 must be adjusted in order to determine 

the  store  fl ow  sensor  temperature  from  which  on 
the heat pump mode becomes active. When the heat 
pump mode is active, the primary pump is run at the 
adjustable 

Speed HP

.

The heat pump mode becomes active in the follow-
ing cases:
•  During sliding set value adaptation, the tempera-

ture at the store fl ow sensor falls below T-HP opt.

•  T-HW set has been adjusted lower than T-HP opt 

and the temperature at the store fl ow sensor falls 
below the set temperature calculated.

Only after the cold start phase has been completed, 
will the heat pump mode become active.

Adjustment channel

Description

Adjustment  range / selection Factory setting

HP

Activation of the function

Yes, No

No

T-HP opt

Limit temperature for the heat pump 
control (store mixing)

20 … 75 °C

45 °C

Speed HP

Store mixing pump speed

30 … 100 %

100 %

back

Main  menu / Hot  water / HP

The 

Blocking protection

 function can be used for 

protecting the pumps against blocking after standstill. 
Blocking protection is executed daily at 12 o'clock. 
It will energise relay 4 (primary pump) and, if the 
circulation has been activated, relay 2 (circulation 
pump) as well.
Pump runtime is 3 seconds. First, the circulation 
pump starts. Then, the primary pump starts. The HW 
heating, the hot start of the heat exchanger and the 
circulation have a higher priority than the blocking 
protection. In the case of a draw-off, the blocking 
protection for the corresponding pumps is aborted.

Blocking protection

Adjustment channel

Description

Adjustment  range / selection Factory setting

Blocking protection

Activation of the function

Yes, No

No

Main  menu / Hot  water / Blocking  protection

Summary of Contents for Regtronic RQ









































Reviews: