manualshive.com logo in svg

Outdoor living today 8x4 SpaceSaver Bevel, Assembly Manual

Share
Download
Outdoor living today 8x4 SpaceSaver Bevel Assembly Manual Download Page 27

69.

Position first 

Roof Ridge Board 

(1/2” x 4 1/2” x 51 5/8”) at the rear of roof to cap off shingles

and facia. Ridge Boards should meet on seam of roof panels. When aligned correctly, attach with 
4 - 1 1/2” nails per piece.

70.

Attach 

Facia / Detail Plates

to cover seams where Front and Rear Facia pieces come 

together.  Secure with 4 - 1 1/2” finishing nails per piece.

71.

Attach 

Upper Interior Door Stop

(1/2” x 1/2” x 32”) positioning trim against door
jamb and underneath door header flush to
edges on inside as shown above.  Attach with 
4 - 1 1/2” finishing nails.

32” door stop.

Lower 
interior
door stop.

72.

Attach upper and lower 

Vertical Interior

Door Stops

as per 

Step 71

.   Position against

door jamb and underneath upper door trim. Attach
with 4 - 1 1/2” finishing nails per piece. Complete
both sides.

Door

Header

Toll Free 1-888-658-1658             www.outdoorlivingtoday.com          [email protected]

Page 27

Door
Jamb.

Summary of Contents for 8x4 SpaceSaver Bevel
































Reviews:

No comments

Brands by name

Popular brands

Load more brands