manualshive.com logo in svg

Outdoor living today 8x4 SpaceSaver Bevel, Assembly Manual

Share
Download
Outdoor living today 8x4 SpaceSaver Bevel Assembly Manual Download Page 19

45.

Secure roof panels to walls at both ends by positioning 2 Simpson Strong Ties on plywood and 

outside rafters and securing with 2 - 1 1/4” screws per Strong Tie. Complete both sides. 

Strong Ties. 

46. 

To further secure roof panels from the inside, drill pilot holes on an angle in each panel’s 

Mid Rafter (3 per Rafter). Using 3 - 2 1/2” screws, secure rafters to plywood.  

Note: 

from outside if possible, have a helper push roof panel down so plywood sits flush against

rafter while securing. 

Mid

Rafter

Plywood

3 - 2 1/2” screws Toe
Nailed in each Mid Rafter.

Toll Free 1-888-658-1658             www.outdoorlivingtoday.com          [email protected]

Page 19

44. 

Slide 3rd and 4th 

Filler Shingles

up and underneath appropriate shingle rows and follow 

Steps

41 - 42

to align and attach. On last filler, screws will get covered by Roof Ridge Board (4 1/2” wide).

Note: If Top Siding Pc.
for Angle Wall was not
installed in step 22 it can
be done now. Attach
with 3 - 1 1/2” Finishing
Nails per piece.

Summary of Contents for 8x4 SpaceSaver Bevel
































Reviews:

No comments

Brands by name

Popular brands

Load more brands