background image

19 

or regulator.

 

• 

Insert  lit  match through the  right  match-
lighting  hole  on  the  right  side  of  the 
barbecue body and place near rightmost 
burner porthole. 

• 

Push and turn the rightmost control knob 
anti-clockwise to the high position, taking 
care to protect yourself from the flames. 

• 

When  the  right  burner  is  lit,  turn  the 
remaining burners on from right to left. 

• 

Confirm that each burner is alight before 
turning on the next burner. 

• 

To light the side burner, place the lit end of a 
long match alongside the side burner. Push 
and turn the side burner knob anti-clockwise 
to the high position, taking care to protect 
yourself from the flames.  

• 

If a burner fails to ignite, contact your local 
dealer for assistance. 

• 

After ignition, turn the burners to the high 
position for 3-5 minutes in order to pre-heat 
the barbecue. This should be done before 
each  cooking  session.  The  hood  or  lid 
should be open during preheating.  

• 

After  completion  of  preheating,  turn  all 
burners to the low position for best cooking 
results. 

 

Lighting the Side Burner   

Raise the side burner lid. Push and turn the 
side burner control knob anti-clockwise to the 
high position. Push the ignition button rapidly 
until the side burner ignites. If the side burner 
fails to ignite, turn the control knob to the OFF 
position and wait five minutes before attempting 
to re-light following the above procedure. If the 
side burner still fails to ignite, turn the control 
knob off, wait five minutes and light with match. 

 

When using the side-burner, care should be 
taken to ensure that pans are central and flat on 
the side-burner grid. 
 

Grill Cooking 

The  burners  heat  up  the  flame  tamers 
underneath the grill, which in turn heats the 
food  on  the  grill.  The  natural  food  juices 
produced during cooking fall onto the flame 
tamers below and vaporise. The subsequent 
rising  smoke  bastes the  food,  as it  travels 
upwards,  imparting  that  unique  barbecued 
flavour.  
 

Roasting Hood Cooking 

Barbecues equipped with a roasting hood give 
the option to form  an ‘oven’ for roasting or 

baking food, such as joints of meat or whole 
chickens, etc. More even cooking of food will 
actually be achieved by using the barbecue with 
the hood down. 

However, this should only be 

done with the burners on low.   
 

For best results, place the food you wish to 
bake or roast on a metal baking tray and set it 
on one side of the cooking grill. 
 
Turn the burner directly under the food to the 
OFF position and turn all other burners to a 
LOW to MEDIUM position. 
 
Close the hood to cook the food ‘indirectly’. 
Avoid lifting the hood unnecessarily as heat is 
lost every time the hood is opened. If the hood 
is opened during cooking please allow extra  
time for the barbecue to regain its temperature 
and complete the cooking. Use the temperature 
gauge to monitor the heat of the barbecue. 
 
If the internal heat becomes too high, turn the 
burners down  to  the  low  position.  It  is not 
necessary  or  advisable  to  have  all  of  the 
burners on high when the hood is closed. 
 
DO  NOT  ALLOW  YOUR  BARBECUE  TO 
OVERHEAT. Be careful of  hot steam  when 
opening the hood. 
 

Warming Rack 

 

Warming racks are a convenient way to keep 
cooked food warm or to warm items such as 
bread  rolls.  It  is  advisable  to  place  food 
(particularly  fatty  foods)  to  the  front  of  the 
warming rack to avoid the possibility of juices 
and  fat  running  down  the  back  of  your 
barbecue. Always check that your warming rack 
is properly fitted before use. 

 

Flare-Up Control *Very Important Notice*           

Flare-ups occur when meat is barbecued, and 
its fat and juices fall upon the hot flame tamers. 
Smoke of course helps give food its barbecued 
flavour, but it is best to avoid excessive flare-up 
to prevent food being burned. To control flare-
ups, it is 

ABSOLUTELY ESSENTIAL 

to trim 

away excess fat from meat and poultry before 
grilling,  use  cooking  sauces and  marinades 
sparingly and try to avoid very cheap cuts of 
meat or meat products as these tend to have a 
high fat and water content. Also, the burners 
should always be placed on the low setting 
during cooking.  
 
When flare-ups do occur, they can usually be 

Summary of Contents for MF4493

























Reviews: