background image

ELECTRIC FURNACE

180, 3

e

Avenue, L'Islet (Québec)  G0R 2C0  CANADA

Tel.: 418-247-3947  •  Fax: 418-247-7801

30042408B

www.ouellet.com

• Never tamper with the unit or its controls. User MUST contact

a specialized contractor when a failure occurs. DO NOT 
ATTEMPT to repair.

• When using a humidifier make sure not to damage the heating

element bank.

• We recommend that your unit be inspected by a specialized 

technician once a year.

• Poor maintenance of air filters OR an unbalanced static 

pressure may result in a performance decrease.

• Always use genuine parts for maintenance or service call. 

The use of unbranded parts will void the warranty.

• The use of this unit without an air distribution duct will void 

the warranty.

• It is strictly forbidden to use jumpers to simulate heat demand.
• Risk of electrical shock. Disconnect power before installation, 

servicing, maintenance or field wiring. Replace all panels
before operating. Failure to do so can result in electrical 
shock causing severe injuries or death.

• When performing installation, servicing or cleaning the unit, 

it is recommended to wear safety glasses and gloves.

• To assure a proper performance of your furnace, we recommend

that you use high quality name brand thermostats.

• When applicable local regulation comprises more restrictive 

installation and/or certification requirements, the aforementioned
requirements prevail on those of this document and the 
installer agrees to conform to these at his own expenses.

• For your safety, do not store or use gasoline or other flammable 

liquids and vapors in the vicinity of this unit or any other 
appliance.

• These instructions are intended to be use by qualified personnel

who have been trained in installing this type of furnace. 
Installation of this furnace by an unqualified person may 
lead to equipment damage and/or hazardous condition 
which may lead to bodily harm.

• This furnace is not watertight and is not designed for outdoor 

installation. This furnace shall be installed in such a manner 
as to protect its electrical components from water. Outdoor 
installation leads to a hazardous electrical condition and to 
premature furnace failure, thus voiding the warranty.

• Do not block the combustion air openings in the furnace. 

Any blockage will result in improper overheat situation and 
may result in a fire hazard and/or cause bodily harm.

• The unit must have an uninterrupted or unbroken electrical 

ground to minimize personal injury if an electrical fault 
should occur. When performing electrical connection, the 
ground conductor must be firmly attached to the ground lug 
in the furnace.

• Do not use this furnace as a construction heater. Use of this 

furnace as a construction heater exposes the furnace to 
abnormal conditions, contaminated combustion air and the 
lack of air filters. Failure to follow this warning can lead to 
premature furnace failure and/or vent failure which could 
result in a fire hazard and/or bodily harm. 

• The owner and/or the user is responsible of the following: 

Always maintain the immediate surrounding of the furnace 
free from combustible and highly flammables materials.The 
furnace ambient air should not have an excessive dust 
concentration and humidity. Never operate this central heating
appliance without an air filter. 

• Before performing any service functions, unless operations 

specifically require the power to be on, make sure all utilities 
are turned “OFF” upstream of the appliance. Failure to comply 
with this warning will cause a fire hazard and/or bodily harm.

• All questions regarding the operation, maintenance or warranty

of this unit should be addressed to the company where this 
product has been sold from.

WARNING

!

CAUTION

• Never burn garbage or paper in the heating system and never leave rags or paper around the unit.
• Return air grilles and warm air registers must not be obstructed.

IMPORTANT: All local and national code requirements governing the electrical installation heating equipment, wiring and flue connections
must be followed. Some of the codes that may be applicable are: 
ANSI/NFPA 70 NATIONAL ELECTRICAL CODE
CSA C22.1 CANADIAN ELECTRICAL CODE
Only the latest issues of the above codes should be used, and are available from either: 

The National Fire Protection Agency

Batterymarch Park

Qunicy, MA 02269

The Canadian Standards Association

178 Rexdale Blvd.

Rexdale, Ontario M9W 1R3

or

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

Summary of Contents for Diablo OFR Series











Reviews: