background image

5

4 Required Tools

The following list ensures that you use the right implement for every procedure. You will find the maintenance 

plan at the end of the service instructions manual.

Reversible ratchet handle wrench 

and sockets, sizes 8 – 2

Allen wrenches, 

sizes 2.5 – 8

Wrenches, 

sizes 8 – 24

Water pump pliers DIN 8976, 

gripping width up to 32 mm

Screwdrivers, blade 

widths 2.5/3.5/5.5 mm

Phillips head screwdriver, size 2 mm 

 

Plastic hammer

Hammer approx. 300 g

Side cutting pliers

3 Preface

Regular maintenance is important. It increases safety and prolongs the service life of the product. 

All rehab products should be inspected and serviced once a year. If the product is used frequently, or if it is used by 

growing children or patients with changing clinical conditions, we recommend readjusting and servicing the product 

every 6 months. Use only original spare parts for all service and maintenance. The service and maintenance described 

in this manual should be performed by trained specialists only and not by the user. This service and maintenance 

manual  refers  to  the  spare  parts  catalog  and  Instructions  for  Use.  For  this  reason,  it  is  important  to  use  these 

documents together.

Liquid thread lock ‘medium strength’

Summary of Contents for z50























Reviews: