INS160246
REV031116
LED Book Light
S02GGJ
PL-0086
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with
your new OttLite
®
product.
NOTE: THIS UNIT IS FULLY ASSEMBLED
1.
Remove book light and accessory from packing and place
them on a flat steady surface (a table).
2.
The OttLite LED Book light is powered by 3 AAA batteries
(not included), alkaline or rechargeable batteries are
recommended.
3.
Install batteries per
BATTERY INSTALLATION
procedure.
4.
This LED Book Light can be mounted on a book edge or
placed on a flat surface such as a table.
5.
A USB cord (H) is included with the LED Book Light.
6.
To use USB cord (H), connect input (G) to LED Book Light
connection port (F). Connect USB input (J) to a USB power
source (reference
Figure 1
).
NOTE:
This product does not contain a charging mechanism;
therefore, the USB cord is provided solely as a power source
connection to a USB port such as a computer. During battery
operation,
DO NOT
attach USB to item as it will cut-off DC battery
power.
Follow the selected method of mounting as detailed below.
CLIP MOUNT
1.
To mount or attach LED Book Light, open the clip (B) and
insert Book Light body (A) fully onto appropriate edge and
verify body is held firmly onto book (reference
Figure 3
).
2.
An appropriate edge will be thicker than ¼ inch and less
than 1 inch.
3.
To position the LED light source (D) simply bend the stem
or flex-neck (C) as needed to point the light. Please hold the
body (A) while adjusting the flex-neck (C).
4.
Turn the LED light
ON & OFF
by using power switch (E)
located in the front-upper side of LED Light Source (D).
TABLE USE
1.
Set Book Light body (A) on a steady flat surface such as a table
(reference
Figure 4
).
2.
To position the LED light source (D) simply bend the flex-
neck (C) as needed to point the light. Please hold the body
(A) while adjusting the flex-neck (C).
3.
Turn the LED light
ON & OFF
by using power switch (E)
located in the front-upper side of LED Light Source (D).
DO NOT FORCE
the flexible stem into any extreme positions as
damage may occur.
BATTERY INSTALLATION
1.
Your OttLite LED Book Light is powered by 3 AAA batteries
(not included). With standard alkaline batteries, the LED
Book Light will operate approximately 72 hours. Light output
will slowly diminish as the batteries lose energy.
Warning: Keep away from children. If swallowed,
promptly see a doctor. Do not install backwards,
charge, put in fire or mix with other battery types – may
explode or leak causing injury.
2.
To install batteries, slide battery compartment door (K)
away from the stem while slightly depressing the door near
the tab (reference
Figure 2
).
3.
Install the 3 batteries as indicated by graphic inside the
battery compartment. Battery negative terminals should
point toward the spring.
4.
Replace battery compartment door (K) by laying it on open
compartment and sliding door toward the stem to engage
the tabs to the compartment, a click should be heard as it
locks into place.
Notice: Only replace batteries as a simultaneous set
and do not mix with older batteries. Remove batteries
if consumed or if the light has not been in use for a long
period of time
.
NOTE:
The important safety instructions appearing in this
instruction sheet are not meant to cover all possible conditions
and situations that may occur. It must be understood that
common sense, caution, and care must be used with any
electrical product.
CAUTION:
Any change or modification to product
not expressly recognized by OttLite Technologies voids
OttLite’s responsibility for proper function of product.
FCC PART 15
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different
from that of the receiver.
•
Consult the dealer or an experienced radio/TV technician
for help.
NOTICE:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that
may cause undesired operation
CAN ICES-3 (B) / NMB-3 (B)
Accessories:
USB Cord
J
K
B
C
A
E
D
G
F
H
Figure 1
Figure 2
Figure 3
Figure 4
INS160246
REV030916
English
LED Book Light
