background image

Warnings Statements/Avertisseement

Do not substitute components as this may interfere with the intrinsic safety of the device.

If the unit is past the “Activate Before Date” on the package, please do not activate.

Do not attempt part replacement or substitution as this could impair the intrinsic safety rating and will void the 
warranty of the product.

Ne pas essayer de la remplacer une partie ou la substitution, car cela pourrait nuire à la cote de sécurité intrinsèque 
et annulera la garantie du produit.

Before daily use check the following:

Sensor and Audio ports are clear of any obstructions i.e. debris or blockage

Perform the “Self Test” to ensure proper operation of visual, audible, and vibrating alarms

Confirm receipt of a check mark in the manual test is to be performed make sure to test in a clean air 
environment.

If a unit fails the Self Test or Bump Test please discontinue use of the detector. 

The detector contains a lithium battery that must be disposed of by a qualified recycler.

Do not substitute internal components as this may interfere with the intrinsic safety of the device.

Do not attempt to replace the battery or sensor, this product is designed to be disposable. Changing these 
components will void the warranty.

If you suspect any malfunction or have any technical problems please contact your local Otis Instruments 
representative.

4

Summary of Contents for OI-2100 TOCSIN















Reviews: