OSS EB4400 5-SLOT Gen4 Page 13 Installation Manual Download | Manualshive

Page: 13 / 70

background image

One Stop Systems

EB4400 (5-SLOT BP)

13

1.10

Slot Configurations

Configuration# 1

: Default slot configuration. One Upstream slot and five Downstream slots.

You must have the ARC6 cables attached between the edge of the board and the slot connectors under the backplane. Without those ARC6
cables nothing will work in SLOT 5.

Configuration# 2

: Two Upstream slots (Slot 0 and SLOT 5) with two partitions.



Slot 0: Partition #1 with two Downstream slots



Slot 5: Partition #2 with two Downstream slots

«
...
11
12
13
14
15
...
»

Summary of Contents for EB4400 5-SLOT Gen4







































































Reviews:

No comments

Related manuals for EB4400 5-SLOT Gen4

Brand: IBM Pages: 72

Brand: Amplifier Tech Pages: 36

Brand: H3C Pages: 26

ICS-G7748A Series

Brand: Moxa Technologies Pages: 10

Brand: Zonet Pages: 2

Brand: IOtech Pages: 16

Brand: Waves Pages: 41

Brand: SriHome Pages: 12

ipRocketLink IAD 3086

Brand: Patton electronics Pages: 12

Brand: AMD Pages: 27

Brand: EXAGATE Pages: 7

Brand: Black Box Pages: 12

Brand: AMG Pages: 4

Brand: AXIOMTEK Pages: 2

Brand: Adaptec Pages: 3

Brand: TP-Link Pages: 2

Selenio SNP-GW-3GX32

Brand: Imagine communications Pages: 153

Brand: Behringer Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands