OSS EB4400 5-SLOT Gen4 Page 21 Installation Manual Download | Manualshive

Page: 21 / 70

background image

One Stop Systems

EB4400 (5-SLOT BP)

21

5

GPU / PCIe Cards Installation

This chapter provides information on how to install GPU cards or PCIe cards into your One Stop Systems expansion chassis. More details on the
installation of individual cards are provided by the card’s manufacturer.

Install or plug your PCIe cards in the downstream PCIe slot. There are 7 available downstream slots and one option slot.



Slot 0

is the Upstream slot (aka: Target Slot)



Slots 1, 2, 3

and

4

are downstream slots.



Slot 5

is an option slot. Configurable to upstream or downstream modes.

o

Downstream mode: Use downstream slot for an end-point device (i.e. video card, Ethernet, sound card and etc).

o

Upstream mode: Use upstream slot for an OSS Gen4 target card only.

IMPORTANT: You need the ARC6 cables attached between the edge of the board and the slot connectors under the backplane. Without those
cables nothing will work in slot 8. For more information on the option slot configuration, you can download the installation guide from the OSS
support website.

«
...
19
20
21
22
23
...
»

Summary of Contents for EB4400 5-SLOT Gen4







































































Reviews:

No comments

Related manuals for EB4400 5-SLOT Gen4

Brand: Ubiquiti Pages: 24

DES-3526 - Switch - Stackable

Brand: D-Link Pages: 258

System x3630 M4

Brand: IBM Pages: 7

Brand: Cabletron Systems Pages: 21

Brand: Udoo Pages: 7

DHI-NVR5224-24P-4KS2

Brand: Dahua Pages: 24

3C410012A - OfficeConnect Remote 531 Access...

Brand: 3Com Pages: 72

Brand: Cypress Semiconductor Pages: 9

APS6-400 Series

Brand: Eaton Pages: 114

Brand: IEI Technology Pages: 86

Lite N42B1P Series

Brand: Dahua Technology Pages: 14

Brand: protech Pages: 95

Brand: Hama Pages: 6

Brand: ZyXEL Communications Pages: 422

Brand: 1&1 Pages: 32

WNFB-265AXI(BT)

Brand: Sparklan Pages: 14

Brand: X-Micro Pages: 49

Brand: Airlink101 Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands