background image

 

 

 
 

 

 
Osmo Holz und Color GmbH & Co. KG 
Affhüppen Esch 12, 48231 Warendorf 
 

 

- 8 - 

 
Holzimport 
Industriehobelwerke 
Farbenwerk 

 
www.osmo.de 
 
 

 

 

 

 

• 

For transport in lifts the handle/pole of the machine is to be placed upright to prevent it from 
getting stuck on the hoistway walls.  

• 

Sprays and cleaning agents which are not suited for the intended purpose of the appliance 
must not be used.  

• 

Never use substances which are highly inflammable, combustible, toxic, hazardous to 
health, caustic or irritating.  

• 

Corrective maintenance inclusive of the integration of spray leads and hoses may only be 
carried out by approved after-sales service points or competent qualified personnel being 
familiar with all relevant safety regulations.

 

 

 

  

 

10. Technical Data:

 

 
A.C. motor 

 

 

230 V; 50 Hz 

Rated power   

 

290 W; 1.9 A 

Oscillation speed 

 

1.450 1/min. 

Brush   

 

 

330 mm 

Working height  

 

250 mm 

Working weight 

 

12,5 kg 

Protection class 

 

Cable length   

 

7.5 m 

 
 
Subject to changes within the framework of technical progress. 
 
 
 
 
The above information is given to the best of our knowledge but without liability.  
(dated 01/2009) 
 
 

 

 

Summary of Contents for FloorXcenter









Reviews: