11
12
Step 2 Reset the massage chair
①
Insert one end of the cable insert to the power box jack, the other end insert to the power socket, turn on the
switch on the power box, the massage chair is in powered status.
②
Insert the concave position of the remote
plug to the remote cable socket convex position of the left of the seat, insert tightly then twist the nut tightly.
③
Turn on the on/off button of the tablet remote, then turn off, now the backrest is upping and the seat is
downing. Put the remote on the seat temporarily after the backrest is reset.
④
After the backrest is reset, please
turn off the switch and unplug the power.
①
①
①
②
③
②
Step 3 install the left
、
right shoulder shell
Put the right shoulder shell close to the chair shoulder outside;
②
Insert the 6 buckle cavities and the 3 buckles of the shoulder shell inside to the 6 buckle joints and 3 buckles
of the chair shoulder outside, move the wire harness out from the shoulder shell along the notch on the outside
of the shoulder shell at the same time, push the shoulder shell inward hard to make sure the buckle insert firmly.
③
Install the left shoulder shell in same way(there is no wire harness)
Right shoulder shell
Inside of the right shoulder shell
Chair shoulder outside
①
②
②
Buckle
cavity
Buckle joint
Notch
Buckle
Buckle
Wire
harness
▲
①
Twist down the two M6*20 screws on the front end of the iron frame on both sides of the seat
.②
Put the right armrest
close to the side of the main machine, insert the side wire harness of the chair shoulder to the wire harness socket of the
chair shoulder side.
③
Insert the fixed-axis on the end of the armrest to the card slot pallet on the up of the shoulder side.
Insert the stop block into the fixed hole on the up of the shoulder
.④
Insert the fastenings on the bottom of the armrest to
the card slot pallet on the side of the seat frame;
⑤
Insert firmly the air tube of the armrest to the seat air tap, and insert
firmly the wire harness.
⑥
Aim the fixed panel on the side of the armrest to the fixed shelf hole on the side of the seat
frame,
⑦
Install the left armrest follow the above steps,
then use an Allen wrench to screw in a M6*20 screw to tighten.
there is no wire harness on the left armrest.
①
M6*20 Screw
Two
②
②
Air tap and the
wire harness socket
Wire harness
limit parts
Card slot pallet
Fixed panel
Right armrest
Fixed shelf
Fastenings
Air tube and
wire harness
Card slot pallet
Fixed-axis
Wire harness socket
Fixed hole
③
④
⑤
⑥
③
▲
④
④
①
②
③
⑤
Wire harness
Installation
Installation
Installation 3
Installation 4
Installation
Installation
Tablet and cable plug
Plug dent
Remote control
cable socket
Salient point
Step 4 Install left and right armrest
Note: Do not squeeze the air tube during installation, otherwise it will lead to air leakage or the air bag will not inflate.
Make sure the connection of the fixing plate and wiring harness is firm, otherwise the armrest will fall off or the convenient
hand controller, speaker and Bluetooth will not work
Raise the footrest and
insert the shaft into
the hanging ear
Air tube
Harness plug
Shaft
Rotating shaft
pressure plate
Step 5 Install the legs and footrest.
①
Screw down the legs and footrest hanging ears;
②
Plug the wire harness into the socket;
③
Connect
the air tube of leg-rest with the air nozzle of the main machine firmly;
④
Lift the upper rotating shaft
press plate of the hanging lug, lift the legs and footrest, put the rotating shaft into the main engine
hanging lug, and put the rotating shaft press plate down;
⑤
Tighten the screw;
Note: When connecting the air pipe and the wire harness, the air pipe and the wire harness should not be
wound together.
Wire harness
Air tube
Lower the shaft pressing plate and
screwing the screw
Hanging ears
Screw
Air nozzle
Socket
Pain Relief
Quick Demo
Stretch
Chinese Massage
③
