HYDRAULICS
HYDRAULICS
STANDARD MACHINE FOLD
HYDRAULIC HOSE ROUTING
HOSES ENTER TOOLBAR NEAR MANIFOLD
2 CYLINDER FOLDING TOOLBARS
(
12R30 AND SMALLER CONFIGURATIONS
)
4 CYLINDER FOLDING TOOLBARS
(
12R36 AND LARGER CONFIGURATIONS
)
HOSES ENTER TOOLBAR NEAR MANIFOLD
HOSES ENTER TOOLBAR NEAR MANIFOLD
INTERNAL CYLINDER
INTERNAL CYLINDER
For individual hose identification, refer to the Hydraulic Manifold Block Port Identifcation and Toolbar Hydraulic Hose parts identification .
For individual hose identification, refer to the Hydraulic Manifold Block Port Identifcation and Toolbar Hydraulic Hose parts identification .
7 - 3
HYDRAULIC MANIFOLD BLOCK #180-310
PORT
HOSE ASSIGNMENT
FUNCTION
FOLD
TRACTOR TO MANIFOLD PRESSURE I
SUPPLIES OIL TO MANIFOLD TO EXTEND WING FOLD CYLINDERS
UNFOLD
TRACTOR TO MANIFOLD RETRACT I
SUPPLIES OIL TO MANIFOLD TO RETRACT WING FOLD CYLINDERS
LAWP
TRACTOR TO MANIFOLD PRESSURE II
SUPPLIES OIL TO MANIFOLD TO LIFT MACHINE
LAWR
TRACTOR TO MANIFOLD RETRACT II
SUPPLIES OIL TO MANIFOLD TO LOWER MACHINE
OWP*
MANIFOLD TO LEFT OUTER WING FOLD
AND LATCH CYLINDER TEE FITTING 1
SUPPLIES OIL TO LEFT OUTER WING FOLD CYLINDER AND LATCH CYLINDER DURING FOLDING
OWR*
MANIFOLD TO LEFT OUTER WING FOLD
AND LATCH CYLINDER TEE FITTING 2
SUPPLIES OIL TO LEFT OUTER WING FOLD CYLINDER AND LATCH CYLINDER DURING UNFOLDING
LAWP*
MANIFOLD TO LIFT CYLINDER (BASE END)
SUPPLIES OIL TO LIFT CYLINDER 1 DURING MACHINE LIFTING
LAWR*
FITTED WITH TEE
1. MANIFOLD TO LIFT CYLINDER
(ROD END)
2. MANIFOLD TO TONGUE CYLINDER
(ROD END)
SUPPLIES OIL TO LIFT CYLINDER 1 AND TONGUE CYLINDER DURING MACHINE LOWERING
OWP**
MANIFOLD TO RIGHT OUTER WING FOLD
AND LATCH CYLINDER TEE FITTING 1
SUPPLIES OIL TO RIGHT OUTER WING FOLD CYLINDER AND LATCH CYLINDER DURING FOLDING
OWR**
MANIFOLD TO RIGHT OUTER WING FOLD
AND LATCH CYLINDER TEE FITTING 2
SUPPLIES OIL TO RIGHT OUTER WING FOLD CYLINDER AND LATCH CYLINDER DURING UNFOLDING
LAWP**
MANIFOLD TO LIFT CYLINDER (BASE END)
SUPPLIES OIL TO LIFT CYLINDER 2 DURING MACHINE LIFTING
LAWR**
MANIFOLD TO LIFT CYLINDER (ROD END)
SUPPLIES OIL TO LIFT CYLINDER 2 DURING MACHINE LOWERING
GW*
MANIFOLD TO TONGUE CYLINDER
(BASE END)
SUPPLIES OIL TO TONGUE CYLINDER DURING MACHINE LIFTING
R3**
MANIFOLD TO FOLD CYLINDER RETRACT
TEE FITTING 1
SUPPLIES OIL TO RIGHT MID WING FOLD CYLINDERS DURING UNFOLDING
R4*
MANIFOLD TO FOLD CYLINDER RETRACT
TEE FITTING 2
SUPPLIES OIL TO LEFT MID WING FOLD CYLINDERS DURING UNFOLDING
ST DIV*
MANIFOLD TO GEAR FLOW DIVIDER
SUPPLIES OIL TO MID WING FOLD CYLINDERS DURING FOLDING
P1**, P2*,
and GW**
PORTS NOT USED
PORTS SHOULD BE PLUGGED
NT MANIFOLD BLOCK IDENTIFICATION
The
1tRIPr
®
XDNT
is equipped with a hydraulic manifold block and a gear flow divider located near the top link center mast plates, which directs oil to multiple cylin-
ders that must perform together to accomplish a specific function. Below is a port identification chart of the hydraulic manifold block of the
1tRIPr
®
XDNT
.
NOTE: For specific hydraulic hose specifications, refer to “Narrow Transport Machine Hydraulic Hoses” in the parts section of this manual.
* - Ports located on the left side of the hydraulic manifold block when viewing from the rear of the machine.
** - Ports located on the right side of the hydraulic manifold block when viewing from the rear of the machine.
7 - 2