manualshive.com logo in svg

Orthman 125-082-01-EN-OM, Operator'S Manual, Page: 67 / 86

Share
Download
Orthman 125-082-01-EN-OM Operator'S Manual Download Page 67

OPERATION AND FIELD SETTINGS

1TRIPR II Row Units OM-EN 

5-21

Automatic Reset (AR) Trip 

Linkage

The automatic reset (AR) trip linkage is engineered as a 
significant upgrade from a standard shear bolt for row 
unit and shank protection. 

When a rock or other obstacle is hit underground, the row 
unit tail (1), which includes the shank (2), wavy coulters 
(3), and optional basket (4), can trip up and out of the 
ground. 

When the obstacle is passed over, four powerful reset 
springs (5) will drive the 1tRIPr® II shank back into the 
ground. The AR trip linkage helps to protect valuable 
tooling from breaking and bending in rough and rocky soil 
conditions. The AR trip linkage may help, but will not 
prevent damage from occasional glancing blows.

ORM000270

Figure 5-16

1) Row unit tail

3) Wavy coulter (2 used)

5) Reset spring (4 used)

2) Shank

4) Basket

6) Rock

1

3

2

4

5

6

Summary of Contents for 125-082-01-EN-OM























































































Reviews:

No comments