background image

 

 

 

  2

 

PeerCall User’s Manual

 

You can apply to extend the service before the expiration date. 

2.  Make a Call 

2.1 Standby 

PeerCall will display 

Starting...

 during the power-on process.  There will be a sound 

of Chime once the PeerCall is on and connected successfully.  It will then show the phone 
number for two seconds before entering Standby mode if it is ready for 

Dialup

.  The 

message 

PeerCall 100

 and the current time will be displayed.  The number, i.e. 100, is 

the model number of the product.  One of the TheDHCP, PPPoE, or FxIP will be on to 
indicate the current network connection mode, if it indicate DHCP Failed, it means your 
connection may be PPPoE or FxIP type, please check with your MIS manager or ISP to 
confirm your connection type, and refer to 

5. Phone Set-Up

 to change network mode. 

When user is using the PeerCall, pressing <Exit> button or hanging up the Handset will 
put the phone back in Standby mode.  The PeerCall will be put back to Standby mode 
also if user didn’t press any key for more than 30 seconds, except during talking, 
recording a greeting, or recording voice messages. 

Please note, the first time the user plugs in the PeerCall, the server will assign a phone 

number for it.  The User can always display 

the current PeerCall phone number

 by 

using 

Show System Information

 function. 

The PeerCall would not be able to function properly if it could not connect to a server.  
The message 

Not Ready...

 will be displayed.   PeerCall will automatically try to 

reconnect to the server until a connection is established.  If the service subscription 
has expired, the message 

Service End

 will show on the screen.  For a complete list 

of Power-on Messages, please refer to 

Appendix A

.  The PeerCall is able to receive 

text messages from the server in Standby mode. 

2.2  Dial a Number 

2.2.1 

The user can either pick up the Handset or press any digit to go to Dialup mode 

(section 2.2.2).  For the PeerCall model with a hook, the display will be replaced by 

Please Dial

 with the 

dial tone

2.2.2 

Dial the ten digit PeerCall number.  There is a 

tone

 for each key when pressed.  To 

erase the last digit, press <Clear>.  Press <Exit> or hang up the Handset to put  
PeerCall back to 

Standby

 mode. 

Please note, the user can switch to 

Access a Previous Number

 mode by pressing 

<Previous> or <Next> button 

ONLY

 when all digits are erased.  The user can 

switch to 

Save Phone Book

 mode by pressing <Function> button. 

2.2.3 

Press <OK> to start calling. 

2.2.4 

You will see a 

Calling...

 message (and hear 

Ring Echo Tone

) before the 

receiver picks up the phone (please also refer to 

Answer a Call

). 

If the receiver picks up the phone, you can start talking.  The display will show 

Talking...

, the outgoing (

) icons will be on, the current time, hh:mm mo/dy 

and the elapsed time ee (in minutes) will be displayed. 

Summary of Contents for PeerCall 100













Reviews: