manualshive.com logo in svg

Orolia KANNAD 406 AF, Installation Manual, Page: 9 / 60

Share
Download
Orolia KANNAD 406 AF Installation Manual Download Page 9

TABLE OF CONTENTS

TOC PAGE: 1

MAR 30/2020

INSTALLATION MANUAL OPERATION MANUAL

KANNAD 406 AF / AF-H / AF (6D)

© 2020 Orolia S.A.S. All rigths are strictly reserved.

INTRODUCTION...................................................................................... 1
SYSTEM OVERVIEW .............................................................................. 1

COSPAS-SARSAT System.................................................................... 1

Description.............................................................................................................. 1
World coverage with the COSPAS-SARSAT system ............................................. 2
Environmental improvements of ELTs.................................................................... 2
G-Switch (shock detectors)..................................................................................... 2

KANNAD 406 ELTs Presentation........................................................... 3
LINE REPLACEABLE UNITS ................................................................ 4

Transmitter ............................................................................................................. 4
Bracket ................................................................................................................... 4
Remote Control Panel ............................................................................................ 4
External antenna .................................................................................................... 4

Design features ...................................................................................... 5

General ................................................................................................................... 5
Mechanical design .................................................................................................. 5

Compatibility list ..................................................................................... 6

Remote control panels (RCP)................................................................................. 6
DIN-12 connector or programming dongles............................................................ 6
ELT-NAV System Interface..................................................................................... 6
External antennas................................................................................................... 7

KANNAD 406 AF.................................................................................................. 7
KANNAD 406 AF-H and KANNAD 406 AF(6D) ................................................... 7

SYSTEM FUNCTIONAL DESCRIPTION AND OPERATION ............. 101

Transmitter ......................................................................................... 101
Controls.............................................................................................. 102
Working mode information ................................................................. 103

Off ....................................................................................................................... 103
Self-Test ............................................................................................................. 103
Armed ................................................................................................................. 103
On ....................................................................................................................... 104

Endurance.......................................................................................... 105
Electrical characteristics..................................................................... 106

Electrical interface .............................................................................................. 106

Technical Specifications..................................................................... 107
Activation............................................................................................ 108

Standby mode for automatic activation............................................................... 108
Manual activation................................................................................................ 108

Reset.................................................................................................. 108

Manual reset ....................................................................................................... 108
Reset with Remote Control Panel....................................................................... 108

Self-Test............................................................................................. 108

Summary of Contents for KANNAD 406 AF





























































Reviews:

No comments