Orion OLMU-5520 User Manual Download Page 4

European Union Disposal Information

Cautions for consisting  

Environmental condition for installation

-  Since monitor is very sensitive for physical impact, installation requires considerable 

caution.

-  Minimum clearance(20cm) must be secured for smooth ventilation. (See page 6)

Installation must avoid air tight or near air tight places. Improper ventilation causes 
malfunction and shortens product lifetime by rapid internal temperature rise. If monitor 
has to installed at the improper ventilation, additional ventilation openings or fans must be 
provided to keep the internal temperature between 0 ~ 35˚C.

-  For ground of monitor and application devices, it should be connected as frame ground.

- Considering monitor Max power consumption, check the main electric specification .

Recommended Operating Condition

-  Temperature: 5~35˚C, Humidity: 35~75%, Suitable operating time : under 12 hours a day.

- Do not install the set at the air-tight condition. 

- It is recommended to install the set with good ventilation. 

- Do not install the set at the place of direct sunlight or excessive exposure to lightings. 

Blackening, stains or burning effect on the screen can be occurred by improper 
installation or use against the above recommended conditions.

Consideration for easier service

-   When you design the exterior design for monitor system, consider easier disassembly for 

possible service occasion in the future.

- The sliding Universal Unit of ORION is recommended for easier service.

-  If service people can step into the backside ofmonitor system, it can greatly reduce time 

and effort for service.

-  In case of higher locations, consider the installation location and exterior design for easier 

service.

English

Disposal of old Electrical & Electronic Equipment (Applicable 

throughout the European Union and other European countries 

with separate collection programs)

This symbol found on your product or on its packaging, indicates that this 

product should not be treated as household waste when you wish to dispose 

of it. Instead, it should be handed over to an applicable collection point for the 

recycling of electrical and electronic equipment. By ensuring this product is 

disposed of correctly, you will help prevent potential negative consequences 

to the environment and human health, which could otherwise be caused by 

inappropriate disposal of this product. The recycling of materials will help to 

conserve natural resources.

This symbol is only valid in the European Union.

If you wish to discard this product, please contact your 

local authorities or dealer and ask for the correct method 

of disposal.

Français

Mise au rebut des équipements électriques et électroniques 

usagés (Valable dans l’ensemble de l’Union Européenne ainsi que 

dans les pays européens disposant de programmes distincts de 

collecte des déchets)

Ce symbole appliqué sur votre produit ou sur son emballage indique que ce produit 

ne doit pas être traité comme un déchet ménager lorsque vous voulez le mettre au 

rebut. Il doit au contraire être remis à un site de collecte agréé pour le recyclage 

des équipements électriques et électroniques. En veillant à ce que ce produit soit 

mis au rebut de façon adéquate, vous contribuerez à prévenir les conséquences 

potentiellement négatives sur l’environnement et sur la santé humaine qui risqueraient 

de se produire en cas de mise au rebut inappropriée de ce produit. Le recyclage des 

matériaux contribuera également à économiser les ressources naturelles.

Ce symbole n’est valable que dans l’Union Européenne.

Si vous souhaitez mettre ce produit au rebut, veuillez

prendre contact avec les autorités locales ou avec votre

revendeur et renseignez-vous sur la méthode de mise

au rebut correcte.

Deutsch

Entsorgung von elektrischen & elektronischen Altgeräten (geltend 

für die europäische Gemeinschaft und andere europäische 

Länder mit separaten Sammelprogrammen)

Dieses Symbol, zu finden auf Ihrem Produkt oder dessen Verpackung,

macht Sie darauf aufmerksam, dass dieses Produkt bei der Entsorgung

nicht als Hausmüll behandelt werden darf. Statt dessen sollte es an eine

Sammelstelle zum Recycling von elektrischen und elektronischen Altgeräten

gegeben werden. Helfen Sie mit, potenziell schädliche Einflüsse

auf Umwelt und Gesundheit, die durch eine unsachgemäße Entsorgung

dieses Produktes entstehen können, zu vermeiden und entsorgen Sie

dieses Produkt ordnungsgemäß. Recycling hilft, natürliche Rohstoffe

einzusparen.

Dieses Symbol ist nur innerhalb der europäischen

Gemeinschaft gültig.

Wenn Sie dieses Produkt entsorgen möchten, wenden

Sie sich bitte an Ihre örtliche Behörde und fragen Sie

nach der ordnungsgemäßen Entsorgungsmethode.

Español

Deshecho de equipos eléctricos y electrónicos (aplicable a la 

Unión Europea y a otros países europeos con programas de 

reciclaje independientes)

La presencia de este símbolo en el propio producto o en su material 

de embalaje, indica que no se debe tratar como residuo doméstico 

cuando desee deshacerse de él. En su lugar, debe entregarlo en el punto 

limpio correspondiente de reciclaje de equipos eléctricos y electrónicos. 

Asegurándose de que este producto se desecha de forma correcta, ayudará

a evitar posibles consecuencias negativas para la conservación del 

medioambiente y la salud humana, consecuencias que podrían darse si se 

deshace del producto de forma inadecuada. El reciclado de materiales ayuda 

a conservar los recursos naturales.

Este símbolo solamente es válido en la Unión Europea.

Si desea deshacerse de este producto, póngase

en contacto con las autoridades locales o con su

distribuidor y pida información sobre el método de

disposición adecuado.

Italiano

Smaltimento delle attrezzature elettriche ed elettroniche usate  

(applicabile in tutta la Comunità Europea ed altri Paesi Europei 

che applicano programmi di raccolta differenziata)

Il simbolo trovato sul prodotto, o sulla sua confezione, indica che il prodotto 

non può essere trattato come i domestici quando è il momento di smaltirlo. 

Al contrario, deve essere consegnato ad un centro di raccolta specializzato 

nel riciclaggio di attrezzature elettriche ed elettroniche. Assicurando che il 

corretto smaltimento di questo prodotto, si aiuterà a prevenire potenziali 

conseguenze negative sull’ambiente e sulla salute umana, che possono 

essere provocate da uno scorretto smaltimento di questa attrezzatura. I 

materiali riciclati aiuteranno a conservare le risorse naturali.

Questo simbolo è valido solo nell’Unione Europea.

Per smaltire questo prodotto, mettersi in contatto con

le autorità locali – o con il rivenditore – e chiedere

informazioni sul corretto metodo di smaltimento.

Nederlands

Verwijderen van oude elektrische en elektronische apparatuur  

(toepasselijk in de volledige Europese Unie en andere Europese 

landen met afzonderlijke programma’s voor afvalverzameling)

Dit symbool dat op het product of zijn verpakking is aangebracht, geeft aan 

dat dit product niet mag worden behandeld als huishoudelijk afval als u het 

wilt wegwerpen. U moet het afgeven bij een specifiek verzamelpunt voor de 

recyclage van elektrische en elektronische apparatuur. Door te garanderen 

dat u dit product op de correcte manier wegwerpt, helpt u potentiële 

negatieve gevolgen voor het milieu en de menselijke gezondheid, die zouden 

kunnen worden veroorzaakt door een onrechtmatig wegwerpen van het 

product, te voorkomen. De recyclage van materialen helpt het behoud van 

natuurlijke bronnen.

Dit symbool is alleen geldig in de Europese Unie.

Als u dit product wenst weg te gooien, dient u contact op 

te nemen met uw lokale instanties voor details over de 

gepaste methode voor afvalverwijdering.

Português

Eliminação de equipamentos eléctricos e electrónicos usados 

(aplicável na União Europeia e noutros países europeus com 

programas próprios de recolha destes equipamentos)

Este símbolo, colocado no produto ou na respectiva embalagem, indica

que o produto não deve ser tratado como lixo doméstico aquando da sua

eliminação. Em vez disso, deve ser entregue num ponto de recolha de  

quipamentos eléctricos e electrónicos para posterior reciclagem. Ao garantir

a correcta eliminação deste produto, estará a evitar consequências 

potencialmente negativas tanto para o ambiente como para a saúde humana.  

A reciclagem de materiais ajuda a preservar os recursos naturais.

Este símbolo apenas é válido na União Europeia.

Se quiser eliminar este produto, contacte as entidades

locais ou o seu fornecedor para ficar a saber

qual o método de eliminação correcto.

Polski

Usuwanie zużytego sprzętu elektrycznego i elektronicznego 

(Dotyczy krajów Unii Europejskiej i innych krajów europejskich z 

oddzielnymi programami zbiórki odpadów)

Obecność tego symbolu na produkcie lub na opakowaniu z produktem

oznacza, że tego produktu nie można wyrzucać razem z odpadkami

domowymi. Należy go przekazać do punktu zbiórki w celu poddania

recyklingowi podzespołów elektrycznych i elektronicznych. Usunięcie tego

produktu w prawidłowy sposób, pomoże w zabezpieczeniu przed 

negatywnym wpływem odpadów na środowisko i zdrowie ludzi, 

powodowanym przez niewłaściwe usuwanie produktu. Przetwarzanie 

materiałów pomaga w zachowaniu zasobów naturalnych.

Ten symbol obowiązuje wyłącznie w krajach Unii

Europejskiej.

Informacje dotyczące prawidłowej metody usunięcia

tego produktu, można uzyskać u władz lokalnych lub

u dostawcy.

 

Waste Electrical and Electronic Equipment (WEEE) Directive In 

the European Union, this label indicates that this product should 

not be disposed of with household waste. It should be deposited 

at an appropriate facility to enable recovery and recycling. EEE 

complies with Directive ‘Regulation on the Restriction of the Use 

of Certain Hazardous Substances in Electrical and Electronic 

Equipment’

Waste Electrical and Electronic Equipment(WEEE) 

Directive In the European Union, this label indicates that 

this product should not be disposed of with household 

waste. It should be deposited at an appropriate facility 

to enable recovery and recycling. EEE complies with 

Directive ‘Regulation on the Restriction of the Use of 

Certain Hazardous Substances in Electrical and Electronic 

Equipment’

Svenska

Avfall av förbrukad elektrisk och elektronisk utrustning 

(Tillämpbart i hela Europeiska unionen och andra europeiska 

länder med separata samlingsprogram)

Den här symbolen som finns på din product eller på dess förpackning

påvisar att produkten inte ska behandlas som hushållsavfall när du vill

slänga bort den. Istället ska den lämnas över till en lämplig uppsamlingspunkt 

för återvinning av elektriska och elektroniska utrustningar. Genom att 

tillförsäkra att den här produkten återvinns på ett riktigt sätt hjälper du till med 

att förhindra möjliga negative konsekvenser för miljön och mänsklig hälsa. Det 

kan annars orsakas på grund av olämplig sophantering av den här produkten. 

Återvinning av material kommer att hjälpa till att bevara naturtillgångar.

Den här symbolen är endast giltig inom den

Europeiska unionen.

Om du vill slänga bort den här produkten ska du

kontakta lokala myndigheter eller återförsäljar, och

fråga efter lämplig avfallsmetod

Suomi

Vanhojen sähkö- ja elektroniikkalaitteiden hävittäminen 

(Soveltuva kaikkialla Euroopan unionin alueella, sekä muissa 

Euroopan maissa, joilla on erilliset keräysohjelmat)

Jos tuotteessa tai sen pakkauksessa on tämä symboli, sitä ei pidä

hävitettäessä käsitellä tavallisena kotitalousjätteenä, vaan se kuuluu toimittaa 

sähkö- ja elektroniikkalaitteiden kierrätyspisteeseen. Varmistamalla, että 

tämä tuote hävitetään asiaankuuluvalla tavalla autat estämään mahdollisia 

ympäristölle ja ihmisille koituvia negatiivisia seuraamuksia, joita sen 

vääränlainen hävittäminen voi aiheuttaa. Materiaalien kierrättäminen auttaa 

säilyttämään luonnonvaroja.

Tämä symboli on voimassa ainoastaan Euroopan

unionin alueella.

Jos haluat hävittää tämän tuotteen, ota yhteyttä

paikallisiin viranomaisiin tai jälleenmyyjään ja tiedustele 

asiaankuuluvia hävittämistoimenpiteitä.

 

Waste Electrical and Electronic Equipment (WEEE) Yönergeleri 

Avrupa Birliği'nde bu etiket, ürünün ev elektroniği aletleri atıkları 

ile imha edilemeyeceğini gösterir. 

Kurtarmak ve geri dönüşümünü sağlamak için uygun şartlarda 

saklanması gerekir. EEE Yönetmeliğine Uygundur Ve Elektronik 

Eşyalarda Bazi Zararli Maddelerin Kullaniminin Sinirlandirilmasina 

Dair Yönetmelik.

Waste Electrical and Electronic Equipment (WEEE) 

Yönergeleri Avrupa Birliği'nde bu etiket, ürünün ev 

elektroniği aletleri atıkları ile imha edilemeyeceğini 

gösterir. Kurtarmak ve geri dönüşümünü sağlamak için 

uygun şartlarda saklanması gerekir. EEE Yönetmeliğine 

Uygundur Ve Elektronik Eşyalarda Bazi Zararli Maddelerin 

Kullaniminin Sinirlandirilmasina Dair Yönetmelik.

- 4 -

- 5 -

W

ARNING

W

ARNING

Summary of Contents for OLMU-5520
































Reviews: