background image

4

Operating Recommendations

This new ORECK XL High-Speed Upright is one of the finest, fastest,
and strongest units in its class. You’ll love the way it cleans, gets under
things, and it’s SO lightweight and easy to use.

The following are a few simple suggestions regarding its
operation:

1. When inserting a new disposable paper filter dust bag—FIRST

PUFF OUT and OPEN THE BAG.

2. When the disposable filter dust bag is full, REPLACE IT.

3. If at any time the machine does not pick up properly or makes an

unusual noise, STOP OPERATION and service.

4. Although your upright will pick up pins, paper clips, and other

small objects, it is recommended that these be removed from the
floor before you vacuum. Failure to do so may result in permanent
damage to the motor suction fan and its housing.

5.

WARNING: 

Do not use your vacuum cleaner on damp or wet

surfaces. This will cause damage to the vacuum cleaner and is
dangerous to the user. Damage caused by use on wet or damp
surfaces is not covered under warranty.

6.

REPLACE THE BELT EVERY 6 MONTHS.

7. Change the disposable filter dust bag at least once a month—

even if it is not full! The collected dust in the dust bag can cause
odor, attract moisture, and can affect the efficiency of the cleaner.

8.

DO NOT 

run the vacuum cleaner over the cord. The revolving

brush could damage the cord.

9. Use caution when vacuuming over area rug edges and fringe.

General Information

The performance of your new cleaner greatly depends upon care and
maintenance. The instructions in this manual will guide you in
performing basic care and maintenance. To obtain the most satisfying
years of service read the instructions and keep them handy for future
reference.

Disposable Paper Filter Dust Bags

Disposable paper filter dust bags play a very important role in the
efficiency of your ORECK vacuum cleaner. The purpose of the paper
bag is to trap dirt, but at the same time it must be porous enough to
allow air to pass through. If the paper bag becomes clogged, no air can
pass through the cleaner and cleaning cannot take place, regardless of
the cleaner’s power. 

To keep your cleaner operating at maximum efficiency, change the dust
bag frequently. 

DO NOT FILL ABOVE THE LINE INDICATED ON THE

DUST BAG.

Be sure the disposable paper filter dust bag is installed properly.

All paper dust bags are not the same. Your ORECK disposable
dust bags have been designed to be used with the ORECK cleaner.
Using bags other than genuine ORECK TYPE CC disposable bags
will affect the cleaning ability of your cleaner and could cause
damage to it.

The Belt

The belt on your vacuum cleaner controls the speed of the revolving
brush and is very important for the effective operation of the cleaner. If
the belt becomes stretched or cut, it will cause the revolving brush to
stop completely or slow down. See instructions in the manual for
replacing belt.

An extra belt is stored in the baseplate of your cleaner. When
buying replacement belts, use ONLY ORECK genuine belts. Belts
other than Oreck belts will not operate the revolving brush
correctly and may create undue stress which will cause damage to
the motor and brush bearings. Using belts other than ORECK belts
will void the warranty.

Lubrication

The vacuum cleaner motor bearings are factory lubricated and sealed.
Further lubrication is not required.

Parts List

To assist you in identifying components of your vacuum, the parts have
been numbered as follows:

1

Handle section, upper

2

Tube, lower

3

Power head

4

Outer bag

5

Paper filter dust bag

6

Power cord

7

Retaining spring

8

Bag tension bar

9

Zip fastener

10 On/Off switch
11 Cord hook
12 Plastic loop/cable clamp
13 Connector assembly
14 Fan housing
15 Cord assembly
16 Cord Strain Relief Assembly

Assembly

fig. 1

Before assembling appliance, remove two screws from
connector assembly. Remove cardboard insert by pulling
upward. 

fig. 2

With ON/OFF switch facing the front of the unit, slide
upper handle section over matching section of the
connector assembly. Hold tab of cord strain relief flush
with 

TOP

hole in connector assembly. Insert screw

through hole in tab of cord strain relief and firmly tighten
to connector assembly. Insert remaining screw in bottom
hole of connector assembly and tighten firmly.

NOTE: The power cord comes installed in the cord strain
relief. Should the power cord come loose, simply pinch
the power cord together and slide approximately 1 - 2
inches through hole in cord strain relief. Carefully slide
power cord over clamp on the cord strain relief and pull
excess until the power cord is tightly rested under clamp.

fig. 3

Attach cord to cord clip by pressing cord above and
below clip ensuring the cord is fully rested in clip.

Operating Instructions

Make sure disposable paper filter dust bag is in place. 

DO NOT

operate

the cleaner without a paper filter dust bag. Plug the power cord into an
electrical outlet and press the 

On(l) - OFF(O)

switch on handle assembly

when ready to operate.

Up-Position Lock

fig. 4

Place foot on power head and lean handle back gently to release
lock for vacuum use. Return handle to the full upright position to
engage lock.

NOTE: 

Do not operate the unit while in the upright and locked position.

Do not let the unit run while in any one stationary position for any period
of time. Keep the unit moving while in operation.

For Easy Power Cord Storage

fig. 5

Wrap power cord around cord hook on handle and cord hook on
connector.

1

2

3

4

9

10

11

14

15

16

12

13

5

6

7

8

Summary of Contents for XL SIMLY AMAZING XL5-105HH









Reviews: