background image

20

Additional Safety Information

1 - The apparatus shall not be exposed 

to dripping or splashing and that 

objects filled with liquids, such as vases, 

coffee mugs, glasses etc. shall not be 

placed on apparatus.  

 2 - The mains plug/appliance coupler/

direct plug-in adapter is used as 

disconnect device for the soundbar and 

the subwoofer, the disconnect  device 

shall remain readily operable. 

CAUTION: Danger of remote control 

failure if battery is incorrectly replaced. 

Replace only with the same or 

equivalent type.

WARNING: The remote control 

battery shall not be exposed to 

excessive heat such as sunshine, fire 

or the like. 

Correct Disposal of this product. 

This marking indicates that this product 

should not be disposed with other 

household wastes throughout the 

EU. To prevent possible harm to the 

environment or human health from 

uncontrolled waste disposal, recycle it 

responsibly to promote the sustainable 

reuse of material resources. To return 

your used device, please use the return 

and collection systems or contact 

the retailer where the product was 

purchased. They can take this product 

for environmental safe recycling.

FCC Statement: 

This equipment has been tested and found to comply 

with the limits for a Class B digital device, pursuant 

to part 15 of the FCC Rules. These limits are designed 

to provide reasonable protection against harmful 

interference in a residential installation. This equipment 

generates, uses and can radiate radio frequency energy 

and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that 

interference will not occur in a particular installation. 

If this equipment does cause harmful interference to 

radio or television reception, which can be determined 

by turning the equipment off and on, the User is 

encouraged to try to correct the interference by one or 

more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and 

receiver.

- Connect the equipment into an outlet on a circuit 

different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV 

technician for help.

Caution: Any changes or modifications not expressly 

approved by the party responsible for compliance could 

void the User’s authority to operate the equipment.

Summary of Contents for M9 airSOUND
























Reviews: