background image

10

11

ENGLISH

Manual Watering - Program B:

This will allow you to water only those stations with set dura-
tions in Program B. 

  With the dial in the 

AUTO

 position press the 

MANUAL

  

     

    button. 

  Press the 

NEXT

 

button until the display reads “B  

    MANUAL ALL”.

  Press the 

ENTER

 

button.

Each station will water, in sequence, one after another, for the 
same duration specified in Program B. To quickly advance from 
one station to the next press 

NEXT

         .

To abort this process before the manual watering is finished, 
tpress 

CLEAR

       

. Otherwise, the timer will automatically 

exit the “B – MANUAL ALL” mode after all Program B stations 
have run. 

Manual Watering - Single Stations:

This will allow you to water a single station at a time.

  With the dial in the 

AUTO

 position press the 

MANUAL

  

     

    button. 

  Press the 

NEXT

 

button until the display reads     

    “MANUAL STATION 1”.

  Press the 

NEXT

 

button to select the station number  

    you want to water.

  Press the 

or 

buttons to select the number of min- 

    utes to water that station (from 1 to 120 minutes).

  Press the 

ENTER

 

button.

To abort this process before the manual watering is finished, 
press 

CLEAR

       

. Otherwise, the timer will automatically exit 

the “MANUAL – STATION” mode after the selected station has 
run.

Rain Delay Function:

You can press the 

RAIN DELAY

 button to stop all programmed 

watering from taking place for a certain number of hours or 
days (for instance, after a rain storm).

  With the dial in the 

AUTO

 position press the 

RAIN DELAY

  

    button. 

  Press the 

or 

buttons to change the rain delay 

    period. The options are: 24 hours, 48 hours, 72 hours, 4 
    days, 5 days … and up to 99 days in one-day increments.

  Press the

 ENTER

 

button to enter the rain delay mode.  

    The Rain Delay hours remaining will show on the display.

The timer will revert to the programmed schedule at the expira-
tion of the rain delay period. To return to the programmed 
schedule before the expiration of the rain delay period, press 
the 

CLEAR

 

button.

Manual Advance During Watering:

  Pressing the 

NEXT

 

button will advance watering from  

    the current station to the next station in the cycle. This can  
    be done during scheduled, manual, or remote actuated  
    watering.

Section 4: 

Using the Remote 

Control Device

NOTE: The timer will accept commands from the remote control 
device only when the selection dial is turned to 

AUTO

 or 

OFF

. (If 

the selection dial is turned to any other setting, commands from the 
Remote Control Device will be stored in memory and executed when 
the selection dial is turned to 

AUTO

).

Install a Battery in the Remote Control Device:

•  

Open the battery compartment door. 

•  

Install a 9-volt battery in the battery compartment. 

•  

Replace the battery compartment door.

To Synchronize the Remote Control Device 
with the Timer:

The remote device provided with your timer is already synchro-
nized to your timer. If the remote is not functioning properly or 
if you are adding a new remote or RF sensor to your system do 
the following:

•  

With the remote device in your hand press the “

RF Sync

”  

    button on the timer (this will activate a red light on  
    the timer). 

•  

Press the 

OFF

 button on the remote or depress the stem of  

    the RF sensor (the red light should start blinking). 

•  

If the red light blinks you have successfully synchronized the  

    devices. If the light does not blink check that the remote has a  
    fresh 9V battery or that the RF sensor switch is not OFF and  
    try the steps again.

To Water All Stations:

•  

Press and release the 

ALL 

button on the remote control  

    device to select all stations for watering.

•  

Press and release the 

ON “X” MIN

 button to command the  

    timer to water all the stations sequentially for the desired  
    (“X”) number of minutes.

•  

If you wish to advance to the next station before a station's  

    watering duration is complete, press 

NEXT

.

To Water One Station:

•  

Press the number of the station you wish to water. 

•  

Press 

ON "X" MIN 

to water the station for the desired ("X")  

    number of minutes.

 
To Water More Than One Specific Station:

•  

Press the numbers of the stations you wish to water. (Example:  

    3, 7, 10, and 6. The timer will water in sequence from lowest  
    to the highest. 3, 6, 7, 10.) (No matter which order you press  
    the keys, the timer will water them sequentially from the  
    lowest to the highest number.)

C

C

C

Summary of Contents for ST2-RF





















Reviews: