OrangeRx TX6i Instruction Manual Download | Manualshive

Page: 23 / 24

background image

System settings

23

6 CHANNEL TRANSMITTER
DIGITAL PROPORTIONAL RADIO
CONTROL SYSTEMPROGRAMABLE SYSTEM

Firmware Ver.

This function shows information about the transmitters currently installed firmware version.

Firmware update

The function is for updating the system firmware.

Setup:
1. Download the latest firmware from

www.hobbyking.com

2. Open the firmware update on a computer and connect the system via USB cable.
3. Select [Firmware Update] from the systems function menu. Press the wheel, the system will

show a prompt, “This will enter firmware update mode and halt other functions” with an option to
continue, select “Yes”.

*When in update mode the system will show a prompt, “Update mode active. Turn the system off
and on again to exit”.
4. Once the system has been recognized by the computer select the update button.
*Once the system has been updated it will restart.
*Once the system has restarted it is safe to remove the USB cable.

RF module ver.

This function shows information about the receivers currently installed RF module version.

«
...
21
22
23
24
»

Summary of Contents for TX6i

























Reviews:

No comments

Related manuals for TX6i

Brand: Bacharach Pages: 2

FTM-350R - SOFTWARE UPDATE PROCEDURE 7110

Brand: Yaesu Pages: 18

FTM-350R - SOFTWARE UPDATE PROCEDURE 7110

Brand: Yaesu Pages: 67

Brand: Yaesu Pages: 176

FTDX5000 CAT BOOK

Brand: Yaesu Pages: 148

Brand: Yaesu Pages: 56

Brand: Yaesu Pages: 12

Brand: Yaesu Pages: 98

Brand: Yaesu Pages: 96

Brand: Yaesu Pages: 48

Brand: Yaesu Pages: 53

Brand: Yaesu Pages: 98

Brand: Yaesu Pages: 46

Brand: Yaesu Pages: 156

Mark-V FT-1000MP

Brand: Yaesu Pages: 4

Brand: Yaesu Pages: 156

FTDX-9000 Contest

Brand: Yaesu Pages: 12

Brand: Yaesu Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands