OrangeRx TX6i Instruction Manual Download | Manualshive

Page: 12 / 24

background image

Reset Switch – Turn the Roller Button to reset the switch 1 to 8 or None to position up, mid or

down
Press and hold the Roller button to save an exit
or press the cancel key to exit without saving

Down and up Mode:

Timer State – Turn the Roller button to select “Stop” or “Run”. If “Run” is selected, the timer is

counted up

Reset - Press and hold the cancel key to reset the timer if needed, then press the Roller button

Set up – Turn the Roller button to set the time in min. and sec.

Enable Switch – Turn the Roller Button to enable the switch 1 to 8 or None to position up, mid

or down

Reset Switch – Turn the Roller Button to reset the switch 1 to 8 or None to position up, mid or

down

Press and hold the Roller button to save an exit

or press the cancel key to exit without saving

a. Use the wheel to change the status of the switch then press the wheel.

b. Use the wheel to change the reset switch then press the wheel.

c. Use the wheel to change the status of the switch then press the wheel.

d. Press and hold the wheel to save an exit, or press the cancel key to exit without saving.

12

6 CHANNEL TRANSMITTER
DIGITAL PROPORTIONAL RADIO
CONTROL SYSTEMPROGRAMABLE SYSTEM

Up Mode:

Reset - Press and hold the cancel key to reset the timer if needed, then press the Roller button
Thr. pos - Turn the Roller button to change the throttle trigger point.
Press and hold the Roller button to save an exit
or press the cancel key to exit without saving

Down Mode:

Reset - Press and hold the cancel key to reset the timer if needed, then press the Roller button
Thr. pos - Turn the Roller button to change the throttle trigger point.
Set up – Turn the Roller button to set the time in min. and sec.
Press and hold the Roller button to save an exit
or press the cancel key to exit without saving

Down / Up Mode:

Reset - Press and hold the cancel key to reset the timer if needed, then press the Roller button
Thr. pos - Turn the Roller button to change the throttle trigger point.
Set up – Turn the Roller button to set the time in min. and sec.
Press and hold the Roller button to save an exit
or press the cancel key to exit without saving

4.Multi Timer

Mode - Turn the Roller button to select a mode (Up, Down, Down then up)

Up Mode:

Timer State – Turn the Roller button to select “Stop” or “Run”. If “Run” is selected, the timer is

counted up
Reset - Press and hold the cancel key to reset the timer if needed, then press the Roller button
Enable Switch – Turn the Roller Button to enable the switch 1 to 8 or None to position up,
mid or down
Reset Switch – Turn the Roller Button to reset the switch 1 to 8 or None to position up, mid or

down
Press and hold the Roller button to save an exit
or press the cancel key to exit without saving

Down Mode:

Timer State – Turn the Roller button to select “Stop” or “Run”. If “Run” is selected, the timer is

counted up
Reset - Press and hold the cancel key to reset the timer if needed, then press the Roller button
Set up – Turn the Roller button to set the time in min. and sec.
Enable Switch – Turn the Roller Button to enable the switch 1 to 8 or None to position up, mid
or down

«
...
10
11
12
13
14
...
»

Summary of Contents for TX6i

























Reviews:

No comments

Related manuals for TX6i

Brand: Harris Pages: 162

Brand: Harris Pages: 148

Brand: Harris Pages: 4

Brand: Yaesu Pages: 120

Brand: IBR Pages: 20

Brand: Yaesu Pages: 165

Brand: Vestamatic Pages: 2

Long Range Transmitter 2

Brand: Gatekeeper Systems Pages: 5

Brand: Codan Pages: 115

Brand: Audioplex Pages: 2

Brand: marklin Pages: 60

Brand: Firstcom Pages: 44

Brand: M-system Pages: 3

Brand: Vertex Standard Pages: 24

Brand: Icom Pages: 64

Lightolier Controls CLMIR

Brand: Philips Pages: 2

Dynalite DIR-TX8

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands