manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual

The Oracle Netra SPARC S7-2 comes packed with cutting-edge features for optimal performance. To ensure seamless installation, simply download the user manual for free from manualshive.com, and get step-by-step instructions for easy setup. Find everything you need in the comprehensive installation manual, available for hassle-free download.

Share
Download
background image

Locate the Server

Name

Oracle ILOM Target

Service Link

Battery

“Servicing the Battery” on page 189

Cables

“Servicing the Cables” on page 193

DIMMs

/SYS/MB/CMP

w

/MCU

x

/CH

y

/D

z

“Servicing DIMMs” on page 159

Drives

/SYS/DBP/HDD

x

“Servicing SAS Drives” on page 85

Drive backplanes

/SYS/DBP

“Servicing the Drive Backplane” on page 117

NVMe drives

 

“Servicing NVMe Storage Drives” on page 97

Fan modules

/SYS/MB/FM

x

“Servicing Fan Modules” on page 151

Filter

“Servicing the Air Filter” on page 79

LED board

“Servicing the LED Board” on page 217

Motherboard

/SYS/MB

“Servicing the Motherboard” on page 225

Network interfaces

/SYS/MB/NET

x

“Servicing the Motherboard” on page 225

PCIe cards

/SYS/MB/PCIE

y

“Servicing PCIe Cards” on page 169

Internal HBA PCIe card

 

“Servicing the Internal HBA PCIe Card” on page 179

PDB

/SYS/PDB

“Servicing the PDB” on page 141

Power supplies

/SYS/PS

x

“Servicing Power Supplies” on page 131

USB board

 

“Servicing the USB Board” on page 109

eUSB flash drive

 

“Servicing the eUSB Drive” on page 103

Related Information

■

“Removing Power From a Server” on page 49

■

“Accessing Internal Components” on page 55

Locate the Server

You can use the Locator LEDs to pinpoint the location of a server. This procedure is helpful

when you need to identify one particular server from many others in the same rack.

1.

Access Oracle ILOM.

See 

“Log In to Oracle ILOM (Service)” on page 26

.

2.

Turn on the Locator LED.

-> 

set /SYS/LOCATE value=Fast_Blink

The white Locator LEDs (one on the front panel and one on the rear panel) blink.

48

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments

Related manuals for Netra SPARC S7-2

NEC Univerge SV8100 System Maintenance Manual preview
Univerge SV8100
Brand: NEC Pages: 78
NEC Univerge SV8100 General Description Manual preview
Univerge SV8100
Brand: NEC Pages: 186
NEC Univerge SV8100 Configuration Manual preview
Univerge SV8100
Brand: NEC Pages: 150
NEC Univerge SV8100 Service Information Bulletin preview
Univerge SV8100
Brand: NEC Pages: 52
Hanwha WRR-5301 Replacement Manual preview
WRR-5301
Brand: Hanwha Pages: 3
IBM eServer BladeCenter JS20 Type 8842 Installation And User Manual preview
eServer BladeCenter JS20 Type 8842
Brand: IBM Pages: 150
Aaeon AIOT-ILRA01 User Manual preview
AIOT-ILRA01
Brand: Aaeon Pages: 38
Inspur NF5260FM6 User Manual preview
NF5260FM6
Brand: Inspur Pages: 82
Integra NAS-2.3 Instruction Manual preview
NAS-2.3
Brand: Integra Pages: 40
Supero SUPERSERVER 5017C-MF User Manual preview
SUPERSERVER 5017C-MF
Brand: Supero Pages: 96
Supermicro A+ AS-2124US-TNRP User Manual preview
A+ AS-2124US-TNRP
Brand: Supermicro Pages: 130
DNP WSP PRO Quick Start Manual preview
WSP PRO
Brand: DNP Pages: 2
Supermicro A+ AS -2114GT-DNR User Manual preview
A+ AS -2114GT-DNR
Brand: Supermicro Pages: 126
IBM X3850 X6 Installation And Service Manual preview
X3850 X6
Brand: IBM Pages: 1730
Infotrend EonServ 7000 Series Quick Installation Manual preview
EonServ 7000 Series
Brand: Infotrend Pages: 2
Advantech SKY-8101D User Manual preview
SKY-8101D
Brand: Advantech Pages: 38
Overland Storage SnapServer Expansion E2000 Quick Start Manual preview
SnapServer Expansion E2000
Brand: Overland Storage Pages: 5
Overland Storage SnapSAN S3000 User Manual preview
SnapSAN S3000
Brand: Overland Storage Pages: 133

Brands by name

Popular brands

Load more brands