Oracle Netra SPARC S7-2 Service Manual Download Page 151

Page: 151 / 258

Servicing Fan Modules

Caution -

These procedures require that you handle components that are sensitive to ESD,

which can cause server components to fail.

Fan modules are composed of redundant fan elements. This redundancy enables the fan module

to continuously supply air flow, even if one fan element fails. The fan modules are located at

the midsection of the server, behind the air duct. See

“Component Locations (Storage, Power,

NVMe, and Fan Modules)” on page 14

Description

Links

Replace a faulty fan module.

“Locate a Faulty Fan Module” on page 152

“Remove a Fan Module” on page 153

“Install a Fan Module” on page 155

“Verify a Fan Module” on page 157

Remove a fan module as part of another

component's service operation.

“Remove a Fan Module” on page 153

Install a fan module as part of another

component's service operation.

“Install a Fan Module” on page 155

Add fan modules.

“Install a Fan Module” on page 155

“Verify a Fan Module” on page 157

Decrease the number of fan modules.

“Remove a Fan Module” on page 153

Identify a faulty fan module.

“Locate a Faulty Fan Module” on page 152

“Detecting and Managing Faults” on page 25

Related Information

■

“Identifying Components” on page 13

■

“Detecting and Managing Faults” on page 25

■

“Component Service Task Reference” on page 47

Servicing Fan Modules

151

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Oracle Netra SPARC S7-2, Service Manual, Page: 151 / 258

Search results

Summary of Contents for Netra SPARC S7-2

Reviews: