manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual

The Oracle Netra SPARC S7-2 comes packed with cutting-edge features for optimal performance. To ensure seamless installation, simply download the user manual for free from manualshive.com, and get step-by-step instructions for easy setup. Find everything you need in the comprehensive installation manual, available for hassle-free download.

Share
Download
background image

Removing Power From a Server

3.

After locating the server with the blinking Locator LED, turn the LED off by

pressing the Locator button.

Note - 

Alternatively, you can turn off the Locator LED by running the Oracle ILOM 

set

 

/SYS/

LOCATE

 

value=off

 command.

4.

Consider your next step.

■

Service other components.

See 

“Component Service Task Reference” on page 47

.

■

Remove power from the server.

See 

“Removing Power From a Server” on page 49

.

Related Information

■

“Safety Information” on page 44

■

“Component Service Task Reference” on page 47

■

“Accessing Internal Components” on page 55

Removing Power From a Server

These topics describe different procedures for removing power from a server.

Step

Description

Link

1.

Prepare the server for powering off.

“Prepare to Power Off a Server” on page 50

2.

Power off the server by one of three methods.

“Power Off the Server (Oracle ILOM)” on page 50

“Power Off the Server (Power Button -

Graceful)” on page 51

“Power Off the Server (Emergency Shutdown)” on page 52

3.

Disconnect the cords and cables.

“Disconnect Power Cords and Data Cables” on page 52

Related Information

■

“Accessing Internal Components” on page 55

■

“Returning a Server to Operation” on page 235

Preparing for Service

49

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments

Related manuals for Netra SPARC S7-2

Supermicro SUPERSERVER 6034H-X8R User Manual preview
SUPERSERVER 6034H-X8R
Brand: Supermicro Pages: 128
Intel SBXL52 - Server Compute Blade Hardware Maintenance Manual preview
SBXL52 - Server Compute Blade
Brand: Intel Pages: 126
SEH SEH InterCon PS54a-G Hardware Installation Manual preview
SEH InterCon PS54a-G
Brand: SEH Pages: 24
Compaq 244857-001 - TaskSmart - C4000 Model 60_duplicate Specification preview
244857-001 - TaskSmart - C4000 Model 60_duplicate
Brand: Compaq Pages: 9
Cavalry CAXA Series User Manual preview
CAXA Series
Brand: Cavalry Pages: 16
QNAP Turbo NAS TS-219P Troubleshooting Manual preview
Turbo NAS TS-219P
Brand: QNAP Pages: 49
Rasilient AI72 User Manual preview
AI72
Brand: Rasilient Pages: 30
Viavi G4-PT-010-8T Hardware Installation preview
G4-PT-010-8T
Brand: Viavi Pages: 4
USR IOT USR-WIFI232-630 User Manual preview
USR-WIFI232-630
Brand: USR IOT Pages: 44
Lantronix CoBox-Micro User Manual preview
CoBox-Micro
Brand: Lantronix Pages: 110
Inspur i24 Server Acceptance Manual preview
i24
Brand: Inspur Pages: 37
360 Systems ImageServer 2000 Operation Manual preview
ImageServer 2000
Brand: 360 Systems Pages: 135
360 Systems Image Server 2000 V-2000 Operation Manual preview
Image Server 2000 V-2000
Brand: 360 Systems Pages: 137
GIGA-BYTE TECHNOLOGY R282-P92 User Manual preview
R282-P92
Brand: GIGA-BYTE TECHNOLOGY Pages: 96
GIGA-BYTE TECHNOLOGY R282-P91 User Manual preview
R282-P91
Brand: GIGA-BYTE TECHNOLOGY Pages: 99
GIGA-BYTE TECHNOLOGY G292-Z20 User Manual preview
G292-Z20
Brand: GIGA-BYTE TECHNOLOGY Pages: 142
GIGA-BYTE TECHNOLOGY AMD EPYC R183-Z92-AAD1 User Manual preview
AMD EPYC R183-Z92-AAD1
Brand: GIGA-BYTE TECHNOLOGY Pages: 168
FaxFinder FF240 Administrator'S Manual preview
FF240
Brand: FaxFinder Pages: 116

Brands by name

Popular brands

Load more brands