Oracle Netra SPARC S7-2 Service Manual Download

Page: 44 / 258

Safety Information

Step

Description

Link

“Servicing the LED Board” on page 217

You can now service the USB board, the motherboard, and the

PDB.

“Servicing the USB Board” on page 109

“Servicing the Motherboard” on page 225

“Servicing the PDB” on page 141

Related Information

■

“Identifying Components” on page 13

■

“Detecting and Managing Faults” on page 25

■

“Returning a Server to Operation” on page 235

Safety Information

For your protection, observe these safety precautions when setting up your equipment:

■

Follow all cautions and instructions marked on the equipment and described in the

documentation shipped with your system.

■

Follow all cautions and instructions marked on the equipment and described in the

Netra

SPARC S7-2 Server Safety and Compliance Guide, Compliance Model No.: 9600

■

Ensure that the voltage and frequency of your power source match the voltage and

frequency inscribed on the equipment's electrical rating label.

■

Follow the electrostatic discharge safety practices as described.

Safety Symbols

Note the meanings of these symbols that might appear in this document.

Caution -

There is a risk of personal injury or equipment damage. To avoid personal injury and

equipment damage, follow the instructions.

Caution -

Hot surface. Avoid contact. Surfaces are hot and might cause personal injury if

touched.

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Service Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands