Oracle EXADATA X5-2 Installation Manual Download Page 12

Page: 12 / 72

Back Panel Status Indicators, Connectors, Drives, and PCIe Slots

Call Out

Description

SP OK LED: green

NVM-Express SSDs 0 through 5

NVM-Express SSDs 6 through 11

USB 2.0 connectors (2)

Service Required LEDs (3): Top: Fan Module (amber); Rear: Power Supply (amber);

Overtemp Icon: System Over Temperature Warning (amber)

Related Information

■

“Back Panel Status Indicators, Connectors, Drives, and PCIe Slots” on page 12

■

“Storage Server Components” on page 10

Back Panel Status Indicators, Connectors, Drives, and PCIe

Slots

This section shows the Oracle Exadata Storage Server X5-2 Extreme Flash back panel and

describes its controls, connectors, and status indicators (LEDs).

Call Out

Description

Power supply unit 0 (PS0)

Power supply unit 1 (PS1)

PCIe slot 1 (Oracle PCIe NVMe switch card)

Oracle Exadata Storage Server X5-2 Extreme Flash Installation Guide • July 2018

Summary of Contents for EXADATA X5-2









































































Search results

Summary of Contents for EXADATA X5-2

Reviews:

Related manuals for EXADATA X5-2

Brands by name

Popular brands

Oracle EXADATA X5-2, Installation Manual

Search results

Summary of Contents for EXADATA X5-2

Reviews:

Related manuals for EXADATA X5-2

Brands by name

Popular brands