Oracle Exadata Storage Server X6-2 High Capacity Installation Manual Download Page 12

Page: 12 / 70

Back Panel Status Indicators, Connectors, Drives, and PCIe Slots

Figure

Legend

Description

USB 2.0 connectors (2)

Related Information

■

“Back Panel Status Indicators, Connectors, Drives, and PCIe Slots” on page 12

■

“Storage Server Components” on page 10

Back Panel Status Indicators, Connectors, Drives, and PCIe

Slots

This section shows the Oracle Exadata Storage Server X6-2 High Capacity back panel and

describes its controls, connectors, status indicators (LEDs), and PCIe slots.

Figure

Legend

Description

1 - 2

Rear storage drive 0 (HDD/SSD) and storage drive 1 (HDD/SSD)

3, 4, 10,

PCIe slots 1, 2, 4, 5 (These slots contain the Oracle Flash Accelerator F320 NVMe PCIe Add In Card.)

PCIe slot 3 (This slot contains the Sun Dual Port QDR InfiniBand Host Channel Adapter for PCIExpress

Gen 3.)

Serial management (SER MGT)/RJ-45 serial port

Oracle Integrated Lights Out Manager (ILOM) service processor (SP) network management

10/100/1000BASE-T port (NET MGT)

Oracle Exadata Storage Server X6-2 High Capacity Installation Guide • July 2018

Summary of Contents for Exadata Storage Server X6-2 High Capacity







































































Search results

Summary of Contents for Exadata Storage Server X6-2 High Capacity

Reviews:

Related manuals for Exadata Storage Server X6-2 High Capacity

Brands by name

Popular brands

Oracle Exadata Storage Server X6-2 High Capacity, Installation Manual

Search results

Summary of Contents for Exadata Storage Server X6-2 High Capacity

Reviews:

Related manuals for Exadata Storage Server X6-2 High Capacity

Brands by name

Popular brands