Opus RolLAM 380 Super, User Manual

Page: 17 / 19

8 ROLLER TENSION SETTINGS
Attention: If you have finished laminating
and do not want to use the laminator, insert
a peace of scrap paper between the rollers,
then put the roller tensioner handle to the
Stand By position as image.
7 ROLLER TENSION SETTINGS
►
Generally it is used in Lamination.
! Attention : If you don't want to laminate, insert the wasted paper in the firs top and bottom roller.
And make the roller tension handle set at the Stand By like the right image.
.
10.
TROUBLE SHOOTING
Symptom Cause Possible solution
Machine will not
turn on
a. Power plug is not plugged
in.
a. Plug the power cord into appropriate
outlet
b. Power switch is "off"
position.
b. Put the power switch to the "on" position.
c. Tripped circuit breaker. c. Reset the circuit breaker.
d. Blown main power fuse. d. Replace the fuse.
There is power, but
the rollers are not
running after the hot
button is pressed:
a. Emergency switch is
engaged.
a. Disengage the emergency switch.
b. Safety cover is not closed.
b. Close the safety cover to active the
safety switch.
c. Guide table is not installed
correctly.
c. Properly install the paper guide so that
the micro switch is activated.
d. Blown motor fuse. d. Replace the motor fuse.
The unit is not
heating up
a. The machine is in "COLD"
mode.
a. Switch to "HOT" mode.
b. Set temperature is lower
than
the room temperature.
b. Raise the temperature according to the
recommended film temperature.
Curled lamination
a. Upward curl a. Loosen the top roll film tension.
b. Downward curl b. Loosend the bottom roll film tension.
Unclear lamination
a. The main roller
temperatures
are too low and lamination
speed is too fast.
a. Raise the roller temperatures and lower
the lamination speed.
Lamination
Stand by
9 RECOMENDED FOIL PARAMETERS
OPUS RolLAM 720, 380 Super • User guide
EN
17
POUCH OBJECT
SETTINGS
TEMPERATURE SPEED
Less than 50 μm
50 μm 100 μm
100 μm 150 μm
150 μm 250 μm
less than 100 g 720 mm wide 115
115
120
125
3,0 m/min
2,7 m/min
2,2 m/min
1,1 m/min
Less than 50 μm
50 μm 100 μm
100 μm 150 μm
150 μm 250 μm
100 g to 150 g 720 mm wide 115
115
120
125
2,7 m/min
2,2 m/min
1,6 m/min
1,1 m/min
Less than 50 μm
50 μm 100 μm
100 μm 150 μm
150 μm 250 μm
150 g to 300 g 720 mm wide 115
115
120
125
2,2 m/min
1,6 m/min
1,3 m/min
1,1 m/min
Over 50 μm
50 μm 100 μm
100 μm 150 μm
150 μm 250 μm
over 300 g 720 mm wide 115
115
120
125
1,6 m/min
1,3 m/min
1,1 m/min
0,8 m/min
Correct temperature and speed can be changed according to material.
It is recommended to do a test before laminating originals.
Should the adhesion not be satisfactory increase the temperature by small levels.
In continuous operation if the temperature is not stable, reduce the speed.
When in continuous use the temperature may fluctuate.