13
12
www
.
opuscamper
.
us
| 925.215.7315
www
.
opuscamper
.
us
| 925.215.7315
op LITe 2021 o
wner
’
s
m
anuaL
op LITe 2021 o
wner
’
s
m
anuaL
S
tEP
5: S
ECURE
yOUR
t
ENt
S
tEP
5: S
ECURE
yOUR
t
ENt
S
tEP
7: S
ECURE
S
tRAP
b
S
tEP
7: S
ECURE
S
tRAP
b
S
tEP
6: S
ECURE
S
tRAP
A
S
tEP
6: S
ECURE
S
tRAP
A
S
tEP
8: S
ECURE
AIR b
EAM
S
tEP
8: S
ECURE
AIR b
EAM
•
Your tent comes with two securing straps on each rear side of
your OP Lite.
•
Strap A gets secured to the hook located on the top rear of
your trailer.
•
Strap B should be secured to the hook located under your
OPUS as shown in the diagram.
•
Pull tightly on the left side rear securing straps as shown.
•
Tighten strap A around the hook and secure strap to trailer.
•
Pull Strap B below the trailer and secure it to the dark grey
hook located directly above the blue handle on your stabilizer
leg.
•
Attach the rear support beam to the trailer by placing the
velcro end of the tent beam to the velcro patch on the trailer.
•
Check that the input hose is in the air beam.
A
A
B
B
Strap A
Strap A
Strap B
Strap B
S
tEP
9: A
CtIvAtE
AIR
S
tEP
9: A
CtIvAtE
AIR
S
tEP
10: S
ECURE
R
EAR
S
tRAPS
S
tEP
10: S
ECURE
R
EAR
S
tRAPS
S
tEP
11: l
EvEl
yOUR
t
RAIlER
S
tEP
11: l
EvEl
yOUR
t
RAIlER
S
tEP
12: S
lIdE
-
OUt
k
ItChEN
S
tEP
12: S
lIdE
-
OUt
k
ItChEN
•
Turn on the AIR Compressor
•
Power and press the AIR inflation button on the Control Panel.
•
Don’t forget to make sure all 4 quick release valves on the
AIR tent are closed and that the AIR compressor hose is in the
AIR tent inlet valve!
•
As the tent is inflating, pull tightly on the rear securing straps.
•
Tightly anchor the straps to a secure object such as a tree or
rock.
•
Whilst the tent is inflating, level and stabilize the trailer.
•
Fold down the stabilize leg by pulling out the blue handle.
•
Use the included corner steady winder or 3/4’’ hex socket
cordless drill/driver attachment, wind down each corner
steady leg until it touches the ground.
Wait for the tent to inflate to its full
height before entering the camper.
The compressor may still be running after
the tent has extended to its full height; this is normal and is simply the
compressor increasing the PSI to the required setting to make the Air
Poles appropriately inflated. Once the correct air pressure is achieved the
compressor will shut off automatically. There is no need to press the button
again.
IMPORTANT: Do not set up the interior of the camper until the tent has
inflated to its full height. This can be identified by the visual ‘popping-up’
movement of the camper and by the straightening of the air poles.
•
Gently press the blue latches to unlock the slide-out kitchen.
•
Connect your quick connects and fold down your kitchen
support leg.
•
Set up your sink drain and waste water carrier.
•
Reference pgs 16 and 17 for setting up your kitchen and fridge.
AIR
AIR
Compressor
Compressor
Power
Power
AIR
AIR
Inflation
Inflation
Button
Button
set
-
up
guide
set
-
up
guide
