Optoma GT-7000 Service Manual Download

Page: 36 / 72

HD65/GT-7000/HD700X

Confidential

4-5

2. Light Leak

Procedure

- Test equipment: video generator.

- Test signal: analog 1280 x 720@60Hz

- Test Pattern: gray 30 patterns

- Check if the light leaks.

* Light leak on reflective edge, eyecatcher, bond

wires and exposed metal.

Inspection item

- Light leak check.

- Bright blemish (dirty).

Criteria

- The pattern cannot accept the color level of the

leakage is brighter than the gray 30 pattern.

- Ref. below table

Note: The defect criteria follows TI specification.

3. Blemish (Dark)

Procedure

- Test equipment: video generator.

- Test signal: analog 1280 x 720@60Hz.

- Test Pattern: blue 60

Inspection item

- Dark blemish check.(dirty)

Criteria

- The bright blemish is unacceptable when it ap

pears on blue 60 pattern.

- Ref. below table

Note: The defect criteria follows TI specification.

4. Dead Pixel (Bright pixel)

Procedure

- Test equipment: video generator.

- Test signal: analog 1280 x 720@60Hz.

- Test Pattern: full black

Inspection item

- Bright pixel check.

Note: Frame dimension under operative zone1

inch

Criteria

- Bright pixel is unacceptable.

- Ref. below table

Note: The defect criteria follows TI specification.

Gray 30

Blue 60

Full black

Summary of Contents for GT-7000









































































Search results

Summary of Contents for GT-7000

Reviews:

Related manuals for GT-7000

Brands by name

Popular brands

Optoma GT-7000, Service Manual

Search results

Summary of Contents for GT-7000

Reviews:

Related manuals for GT-7000

Brands by name

Popular brands