Optoma GT-7000 Service Manual Download

Page: 13 / 72

HD65/GT-7000/HD700X

Confidential

2-4 Disassemble Top Cover

Module

1. Press yellow square region on Top

Cover to make Zoom Ring Cover leap

from fillister.

2. Unscrew 4 screws on the unit base.

Note: - When you disassemble Top Cover,you

must disassemble Lamp Cover

first,because there is 1 screw under the

Lamp Cover.

3. Unscrew 3 screws on the besides and 3

connectors (as yellow square).

Note: - Push the top cover (as the parallel

direction),then pull it up,because there

are 8 tenons (as green square) in it.

- Avoid damage by pulling and draging

IR cable and keypad FPC cable.

- Hold the CNNT plug when pulling the

FPC cable is strongly recommended.

Pulling the cable directly from the unit

will cause the cable damages.

- Make sure cables pass through the

wire mounts (as violet square) when

assembling the unit.

Summary of Contents for GT-7000









































































Search results

Summary of Contents for GT-7000

Reviews:

Related manuals for GT-7000

Brands by name

Popular brands

Optoma GT-7000, Service Manual

Search results

Summary of Contents for GT-7000

Reviews:

Related manuals for GT-7000

Brands by name

Popular brands