background image

Revolving nosepiece not in click stop 
position 

Revolve to click-stop position 

Image tinged yellow 

Blue filter not used 

Use blue filter 

Insufficient illumination brightness  Condenser aperture too small 

Readjust aperture 

Condenser position too low 

Correct position 

Dirt  or  dust  on  the  lens  (condenser, 
objective, eyepiece, collector) 

Cleaning 

 
2. Mechanical 

Trouble   

Cause 

Remedy 

Image  not  focusable  with  high 
power objective 

Slide upside-down 

Turn slide cover 

Cover glass too thick 

Use cover glass of specified thickness 
(0.17mm) 

High power objective contacts slide 
when  changed-over  from  low 
power 

Side upside down   

Turn slide over 

Cover glass to thick 

Use cover glass of specified thickness 
(0.17mm) 

Specimen movement unsmooth 

Mechanical  stage  not  securely 
fastened 

Tighten all fastener 

Binocular images not integrated 

Interpupillary  distance  not  correctly 
adjusted 

Adjustment 

Excessive eye fatigue 

Incorrect diopter adjustment 

Correct adjustment 

Inadequate brightness or illumination    Adjust brightness with control dial 

                 
3. Electrical 

Trouble 

Cause 

Remedy 

Lamp dose not light when switched 
ON 

No electrical power   

Check power cord connection 

Lamp bulb not inserted 

Insert correctly 

Lamp failure 

Replacement 

Sudden lamp failure 

Unspecified  lamp  bulb  used  or  input 
voltage too high 

Replace  with  specified  lamp  bulb.  If 
the  same  symptom  occurs  after 
replacing  the  lamp,  contact  your 
dealer 

Insufficient illumination brightness  Unspecified lamp bulb used 

Replace with specified lamp bulb 

Voltage too low 

Increase brightness with control dial 

Flickering 

or 

unstable 

lamp 

brightness 

Lamp bulb about to fail 

Replacement 

Lamp bulb not correctly inserted into 
socket 

Check for positive connection 

 
7. Maintenance 
1. Cleaning Lenses 
Dust is best removed with a soft brush or gauze. 
More persistent dirt, such as fingerprints, grease and oil, may be removed with soft cotton, lens tissue, or 
gauze lightly moistened with absolute alcohol (ethyl or methyl alcohol). 
To clean immersion oil off the oil-immersion type objective, use lens tissue, soft cotton or gauze lighty 
moistened with petroleum benzine only. 

Summary of Contents for A12.1010

















Reviews: